foratvise
Get Started

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 112 studies that could observe it (sparse evidence).

What happens

Steps such as visual inspection, manual cap placement and manual staging or storage of finished product are carried out by hand because the line lacks automation for these functions, inserting labor-paced activities into an otherwise machine-paced flow. These tasks do not transform the product and add cycle time and variability that depend on operator availability and pace rather than equipment design rate.

What is done about it

Automate the manual functions that are feasible, such as vision-based inspection, mechanized cap placement, and conveyorized or robotic handling of finished goods, to remove labor-paced steps from the machine-paced flow. Where full automation is not justified, apply lean workplace design and standardized work to minimize the time and variability these manual tasks introduce.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.6% [0.1–1.6%]
Expected share of lost time
0.3% [0.1–0.9%]
Share of lost time when present
57% [46–67%]
Studies / units
112 / 155
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.2%]14 studies
  • Soft drinks, bottled water and juices
    0.7% [0.1–2.5%]33 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.2%]14 studies
  • Bakery and pasta
    0.7% [0.1–2.6%]6 studies
  • Meat, poultry and seafood
    0.7% [0.1–2.5%]6 studies
  • Fruit and vegetable processing
    0.7% [0.1–2.5%]4 studies
  • Grain and oilseed milling
    0.7% [0.1–2.5%]4 studies
  • Sugar and confectionery
    0.7% [0.1–2.6%]4 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.4%]8 studies
  • Animal feed and pet food
    0.7% [0.1–2.4%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.2%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Steps such as visual inspection, manual cap placement and manual staging or storage of finished product are carried out by hand because the line lacks automation for these functions, inserting labor-paced activities into an otherwise machine-paced flow. These tasks do not transform the product and add cycle time and variability that depend on operator availability and pace rather than equipment design rate.

How it looks in SCADA data

Engineering guidance

Because the activity is manual, SCADA/MES usually shows no equipment fault or alarm associated with the time consumed; the signature appears instead as manual or operator-assisted mode flags, extended idle or semi-automatic state durations between automatic cycles, and cycle-time variability not explained by any machine-state alarm. Throughput counters may show gaps or irregular pacing with no corresponding downtime code.

Countermeasure

Engineering guidance

Automate the manual functions that are feasible, such as vision-based inspection, mechanized cap placement, and conveyorized or robotic handling of finished goods, to remove labor-paced steps from the machine-paced flow. Where full automation is not justified, apply lean workplace design and standardized work to minimize the time and variability these manual tasks introduce.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 2.59 h · as reported: “non-value-added tasks (manual inspection, placement of caps, storage of finished products)”
    Show verbatim quote
    The analysis showed that these inefficiencies resulted in an excessive time consumption of about 2.59 hours in non-value-added tasks.