foratvise
Get Started
Idling and minor stops (micro-stops)

Micro-stoppages with reduced running speed

Idling and minor stops (micro-stops)PerformanceWhole line or unspecified equipment

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 53 % of the line's lost time. Reported by 2 of the 127 studies that could observe it (limited evidence).

What happens

Frequent brief interruptions, such as small jams, sensor trips or material misalignments, repeatedly halt and restart the line, forcing operators or the control system to run below design speed to avoid triggering further stops. The combination of many short stops and a lowered pace erodes effective throughput without any single event being long enough to count as a full breakdown.

What is done about it

Apply short-interval micro-stop analysis to identify the recurring trigger points, then address root causes such as sensor sensitivity, guide alignment or component wear so the line can run reliably at its intended speed. Standardize quick-clearance procedures and monitor stop-frequency trends to confirm sustained improvement.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.7% [0.2–1.8%]
Expected share of lost time
0.4% [0.1–1.0%]
Share of lost time when present
53% [41–65%]
Studies / units
127 / 161
Evidence grade
C

Grade C: 2 to 4 studies, or an interval wider than 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.8% [0.1–2.7%]13 studies
  • Soft drinks, bottled water and juices
    1.0% [0.1–3.0%]26 studies
  • Brewing, wine and spirits
    0.8% [0.1–2.9%]11 studies
  • Bakery and pasta
    0.7% [0.1–2.6%]24 studies
  • Meat, poultry and seafood
    0.8% [0.1–2.9%]9 studies
  • Fruit and vegetable processing
    0.8% [0.1–2.9%]7 studies
  • Grain and oilseed milling
    0.8% [0.1–3.0%]6 studies
  • Sugar and confectionery
    1.2% [0.2–4.1%]9 studies
  • Snacks, coffee, tea and other foods
    0.8% [0.1–2.8%]5 studies
  • Animal feed and pet food
    0.8% [0.1–2.9%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.8% [0.1–2.7%]10 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Frequent brief interruptions, such as small jams, sensor trips or material misalignments, repeatedly halt and restart the line, forcing operators or the control system to run below design speed to avoid triggering further stops. The combination of many short stops and a lowered pace erodes effective throughput without any single event being long enough to count as a full breakdown.

How it looks in SCADA data

Engineering guidance

MES/SCADA logs show a high count of very short stop events clustered in time, alternating rapidly between running and stopped states, together with an actual line speed persistently below the nominal setpoint. Alarm history shows repeated minor fault codes with short acknowledgment-to-reset intervals rather than a single sustained downtime entry.

Countermeasure

Engineering guidance

Apply short-interval micro-stop analysis to identify the recurring trigger points, then address root causes such as sensor sensitivity, guide alignment or component wear so the line can run reliably at its intended speed. Standardize quick-clearance procedures and monitor stop-frequency trends to confirm sustained improvement.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 110 min · as reported: “low speed, micro strikes”
    Show verbatim quote
    -Not planned downtimes: 110 minutes, low speed, micro strikes, …
  2. Share of lost time: 67.9 % · as reported: “micro-stoppages and speed reduction”
    Show verbatim quote
    Pareto analysis shows that micro-stoppages and speed reduction alone account for 67.9% of the 130.6 downtime hours
  3. Number of events: 80.0 events · as reported: “micro-stoppage”
    Show verbatim quote
    an 80-event micro-stoppage log