foratvise
Get Started
Idling and minor stops (micro-stops)

Minor stoppage of milling equipment

Idling and minor stops (micro-stops)PerformanceMilling and grinding

In short

It appears in about 2 of every 100 lines studied.

When it appears, it takes on average about 54 % of the line's lost time. Reported by 3 of the 43 studies that could observe it (limited evidence).

What happens

Grinding and polishing machines experience brief interruptions in material flow, caused by small jams, blockages of feed or discharge paths, sensor misreads or momentary mechanical hang-ups in the milling chain. These stoppages are cleared quickly by the operator without needing maintenance intervention, but they repeatedly interrupt the continuous feeding and discharge of grain or kernels through the mill.

What is done about it

Improve feed and discharge path design to reduce jamming points, install sensors and guards that prevent small obstructions from stopping the line, and train operators in rapid clearing procedures. Regular preventive inspection of feed chutes, screens and rollers reduces the frequency of these interruptions.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.8% [0.4–4.8%]
Expected share of lost time
1.0% [0.2–2.7%]
Share of lost time when present
54% [41–65%]
Studies / units
43 / 48
Evidence grade
C

Grade C: 2 to 4 studies, or an interval wider than 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    2.0% [0.2–7.3%]5 studies
  • Soft drinks, bottled water and juices
    2.1% [0.2–8.1%]1 study
  • Brewing, wine and spirits
    2.2% [0.2–7.9%]0 studies
  • Bakery and pasta
    2.1% [0.2–7.5%]0 studies
  • Meat, poultry and seafood
    2.1% [0.3–7.8%]0 studies
  • Fruit and vegetable processing
    2.1% [0.2–7.8%]2 studies
  • Grain and oilseed milling
    2.8% [0.4–8.9%]7 studies
  • Sugar and confectionery
    3.6% [0.6–11.6%]10 studies
  • Snacks, coffee, tea and other foods
    1.9% [0.2–6.2%]5 studies
  • Animal feed and pet food
    2.0% [0.2–6.9%]6 studies
  • Food manufacturing (unspecified or mixed)
    1.9% [0.2–6.7%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Grinding and polishing machines experience brief interruptions in material flow, caused by small jams, blockages of feed or discharge paths, sensor misreads or momentary mechanical hang-ups in the milling chain. These stoppages are cleared quickly by the operator without needing maintenance intervention, but they repeatedly interrupt the continuous feeding and discharge of grain or kernels through the mill.

How it looks in SCADA data

Engineering guidance

SCADA/MES logs show frequent short machine-state transitions to stopped or idle on the grinding or polishing station, each lasting only a few minutes, interspersed with brief operator-reset events and no associated maintenance work order. Feed rate or motor load signals typically drop momentarily and recover without a corresponding fault code, and the frequency of these micro-stops accumulates into a distinct idling counter separate from breakdown stops.

Countermeasure

Engineering guidance

Improve feed and discharge path design to reduce jamming points, install sensors and guards that prevent small obstructions from stopping the line, and train operators in rapid clearing procedures. Regular preventive inspection of feed chutes, screens and rollers reduces the frequency of these interruptions.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 12.1 % · as reported: “idle and minor stoppages”
    Show verbatim quote
    Rata-rata kerugian yang terjadi pada setiap mesin yaitu breakdown losses 0,048%, setup and adjustment losses 0,159%, idle and minor stoppages 12,127%, dan reduced speed losses 11,749%.
  2. Share of planned time: 10.0 % · as reported: “idling and minor stoppages”
    Show verbatim quote
    Rata-rata yang diperoleh dari persentase idling and minor stoppages losses yaitu seebesar 10 %.
  3. Share of lost time: 10.5 % · as reported: “idling and minor stoppages”
    Show verbatim quote
    Kerugian terbesar berasal dari reduced speed losses sebesar 51,09% dan idling and minor stoppages sebesar 10,53%.