foratvise
Get Started
Equipment failure (breakdowns)

Drive motor overload failure (high current draw)

Equipment failure (breakdowns)AvailabilityMilling and grinding

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 0 of the 43 studies that could observe it (sparse evidence).

What happens

Increased mechanical resistance in the milling drivetrain, such as bearing wear, misalignment, rotor binding or product build-up, forces the drive motor to draw abnormally high current to maintain torque. If the condition is not corrected, the motor overheats, its protection trips, and the unit must be stopped and the motor repaired or replaced.

What is done about it

Apply condition-based monitoring of motor current and vibration to detect rising load trends early, and perform preventive bearing lubrication/replacement and drivetrain alignment checks. Where repeated overloads occur, inspect and clear mechanical restrictions in the mill and verify motor sizing and protection settings before returning to service.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.6% [0.1–1.8%]
Expected share of lost time
0.3% [0.0–1.1%]
Share of lost time when present
57% [46–68%]
Studies / units
43 / 48
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.7% [0.1–2.7%]5 studies
  • Soft drinks, bottled water and juices
    0.6% [0.1–2.5%]1 study
  • Brewing, wine and spirits
    0.7% [0.1–2.9%]0 studies
  • Bakery and pasta
    0.7% [0.1–2.8%]0 studies
  • Meat, poultry and seafood
    0.7% [0.0–3.0%]0 studies
  • Fruit and vegetable processing
    0.7% [0.1–2.8%]2 studies
  • Grain and oilseed milling
    0.7% [0.1–2.8%]7 studies
  • Sugar and confectionery
    0.6% [0.1–2.6%]10 studies
  • Snacks, coffee, tea and other foods
    0.7% [0.1–2.8%]5 studies
  • Animal feed and pet food
    0.7% [0.1–2.7%]6 studies
  • Food manufacturing (unspecified or mixed)
    0.7% [0.1–2.6%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Increased mechanical resistance in the milling drivetrain, such as bearing wear, misalignment, rotor binding or product build-up, forces the drive motor to draw abnormally high current to maintain torque. If the condition is not corrected, the motor overheats, its protection trips, and the unit must be stopped and the motor repaired or replaced.

How it looks in SCADA data

Engineering guidance

SCADA shows a sustained or stepwise rise in motor current/amperage above the normal operating band for that drive, often preceding an overload trip alarm and a transition of the machine state to stopped/fault. MES logs an unplanned stop event tied to the specific motor tag, sometimes with repeated trip-reset cycles before final shutdown for maintenance.

Countermeasure

Engineering guidance

Apply condition-based monitoring of motor current and vibration to detect rising load trends early, and perform preventive bearing lubrication/replacement and drivetrain alignment checks. Where repeated overloads occur, inspect and clear mechanical restrictions in the mill and verify motor sizing and protection settings before returning to service.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 3.00 Hr · as reported: “V4: M109 high amps/Change”
    Show verbatim quote
    09/17/16 016791 V4: M109 high amps/Change CMP 0 3 3