foratvise
Get Started
Setup and adjustments

Packaging program change and parameter recalculation

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 56 % of the line's lost time. Reported by 1 of the 112 studies that could observe it (sparse evidence).

What happens

During a format or product changeover on the packaging machine, the operator must select a new program and manually recalculate machine parameters such as counts, dimensions and timings to match the new pack configuration. Because these values are worked out and entered by hand rather than retrieved automatically, the machine remains stopped in setup mode until the correct settings are confirmed and stable production is reached.

What is done about it

Implement a recipe management system that stores validated parameter sets per format so the correct values are recalled automatically instead of recalculated manually, and apply SMED principles to separate internal from external setup tasks. Pre-calculation sheets, guided HMI changeover wizards and operator training on the recalculation logic further reduce the time the machine stays idle during the switch.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.3%]
Expected share of lost time
0.3% [0.1–0.7%]
Share of lost time when present
56% [43–66%]
Studies / units
112 / 155
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.0%]14 studies
  • Soft drinks, bottled water and juices
    0.7% [0.1–2.2%]33 studies
  • Brewing, wine and spirits
    0.5% [0.1–1.9%]14 studies
  • Bakery and pasta
    0.6% [0.1–2.2%]6 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.2%]6 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.3%]4 studies
  • Grain and oilseed milling
    0.6% [0.1–2.0%]4 studies
  • Sugar and confectionery
    0.6% [0.1–2.1%]4 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–1.9%]8 studies
  • Animal feed and pet food
    0.6% [0.1–2.1%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.0%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During a format or product changeover on the packaging machine, the operator must select a new program and manually recalculate machine parameters such as counts, dimensions and timings to match the new pack configuration. Because these values are worked out and entered by hand rather than retrieved automatically, the machine remains stopped in setup mode until the correct settings are confirmed and stable production is reached.

How it looks in SCADA data

Engineering guidance

The line or packaging machine shows an extended stop in setup/manual or program-edit state with no good-unit counter increments, often preceded by a recipe or program-selection event in the HMI log. Parameter write events to PLC registers cluster in a short window, and the downstream and upstream equipment show starvation or blocking states for the duration of the change.

Countermeasure

Engineering guidance

Implement a recipe management system that stores validated parameter sets per format so the correct values are recalled automatically instead of recalculated manually, and apply SMED principles to separate internal from external setup tasks. Pre-calculation sheets, guided HMI changeover wizards and operator training on the recalculation logic further reduce the time the machine stays idle during the switch.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 5.00 min · as reported: “Change and calculate program”
    Show verbatim quote
    9 Troca e cálculo do programa 01:29:00 01:34:00 00:05:00 00:05:00 -
  2. Lost time: 5.00 min · as reported: “Change and calculate program”
    Show verbatim quote
    1 Troca e cálculo do programa 00:00:00 00:05:00 00:05:00 - -
  3. Lost time: 5.00 min · as reported: “Loading the operating program”
    Show verbatim quote
    โหลดโปรแกรม 1 5