foratvise
Get Started
Idling and minor stops (micro-stops)

Pallet Supply Depletion

Idling and minor stops (micro-stops)PerformanceFilling

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 52 % of the line's lost time. Reported by 0 of the 120 studies that could observe it (sparse evidence).

What happens

The line runs out of empty pallets available for stacking or supporting finished containers, so the filling or downstream accumulation station must halt until an operator brings in a fresh supply. This is a logistical replenishment gap rather than an equipment malfunction, typically caused by delayed material handling or insufficient buffer stock near the line.

What is done about it

Establish a minimum buffer stock of empty pallets near the end of line with a visual or automated low-level alert that triggers replenishment before depletion, and consider kanban-style or automated pallet dispensing to decouple pallet supply timing from line operation.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.3% [0.1–1.0%]
Expected share of lost time
0.2% [0.0–0.5%]
Share of lost time when present
52% [40–64%]
Studies / units
120 / 162
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.5%]18 studies
  • Soft drinks, bottled water and juices
    0.3% [0.0–1.3%]44 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.5%]16 studies
  • Bakery and pasta
    0.4% [0.0–1.6%]0 studies
  • Meat, poultry and seafood
    0.4% [0.0–1.6%]6 studies
  • Fruit and vegetable processing
    0.4% [0.0–1.7%]4 studies
  • Grain and oilseed milling
    0.4% [0.0–1.6%]6 studies
  • Sugar and confectionery
    0.4% [0.0–1.5%]3 studies
  • Snacks, coffee, tea and other foods
    0.4% [0.0–1.4%]6 studies
  • Animal feed and pet food
    0.4% [0.0–1.6%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.4% [0.0–1.5%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The line runs out of empty pallets available for stacking or supporting finished containers, so the filling or downstream accumulation station must halt until an operator brings in a fresh supply. This is a logistical replenishment gap rather than an equipment malfunction, typically caused by delayed material handling or insufficient buffer stock near the line.

How it looks in SCADA data

Engineering guidance

The affected machine state shows a short idle or stop with no fault code logged, often accompanied by blocking of upstream filling or capping stations and starvation further downstream once accumulation buffers empty out. A pallet presence or low-stock sensor, if instrumented, will register an empty or low condition just before the stop event.

Countermeasure

Engineering guidance

Establish a minimum buffer stock of empty pallets near the end of line with a visual or automated low-level alert that triggers replenishment before depletion, and consider kanban-style or automated pallet dispensing to decouple pallet supply timing from line operation.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 93.0 min · as reported: “pallet ran out”
    Show verbatim quote
    In the month February – May 2019 recorded existence minor idling downtime stop at line 4 , namely , CIP ( Cleaning In Place ) 2,509 minutes , SIP ( Sanitation In Place ) 1,943 minutes , stuck stamp on track 484 minutes , bottle stuck in the SIPA 322 divider , tilting was stuck for 277 minutes and the pallet ran out for 93 minutes .