foratvise
Get Started
Equipment failure (breakdowns)

Pressure sensor/transmitter calibration drift (autoclave)

Equipment failure (breakdowns)AvailabilitySterilization (retort, UHT)

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 58 % of the line's lost time. Reported by 1 of the 34 studies that could observe it (sparse evidence).

What happens

The pressure transmitter or gauge controlling the retort loses accuracy over time due to mechanical wear, diaphragm fatigue, electronic drift or fouling, so the measured pressure no longer matches the true chamber pressure. When the deviation exceeds the allowed tolerance the control or safety interlock detects an inconsistent reading and forces the sterilizer to stop so the process cannot continue with an unverified pressure signal.

What is done about it

Implement a scheduled calibration and verification program for pressure transmitters and gauges against a certified reference, with redundant sensors and automated cross-checking to flag drift before it causes a stop. Replace or recondition sensing elements on a condition- or time-based schedule and log calibration history in the maintenance system.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.1% [0.2–3.2%]
Expected share of lost time
0.6% [0.1–1.9%]
Share of lost time when present
58% [47–68%]
Studies / units
34 / 37
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.2% [0.1–4.9%]5 studies
  • Soft drinks, bottled water and juices
    1.3% [0.1–5.3%]2 studies
  • Brewing, wine and spirits
    1.3% [0.1–5.5%]1 study
  • Bakery and pasta
    1.3% [0.1–5.3%]0 studies
  • Meat, poultry and seafood
    1.9% [0.2–7.6%]1 study
  • Fruit and vegetable processing
    1.2% [0.1–4.7%]2 studies
  • Grain and oilseed milling
    1.2% [0.1–4.9%]6 studies
  • Sugar and confectionery
    1.2% [0.1–4.9%]3 studies
  • Snacks, coffee, tea and other foods
    1.2% [0.1–4.9%]3 studies
  • Animal feed and pet food
    1.2% [0.1–4.9%]4 studies
  • Food manufacturing (unspecified or mixed)
    1.2% [0.1–4.6%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The pressure transmitter or gauge controlling the retort loses accuracy over time due to mechanical wear, diaphragm fatigue, electronic drift or fouling, so the measured pressure no longer matches the true chamber pressure. When the deviation exceeds the allowed tolerance the control or safety interlock detects an inconsistent reading and forces the sterilizer to stop so the process cannot continue with an unverified pressure signal.

How it looks in SCADA data

Engineering guidance

SCADA/MES shows a pressure alarm or deviation alarm (measured vs. redundant reference sensor) coinciding with an unplanned autoclave stop, often preceded by slow trend drift rather than a sudden step change. The cycle log records failed pressure validation or calibration-check faults, and the retort state transitions to fault/hold with no associated jam or mechanical fault code.

Countermeasure

Engineering guidance

Implement a scheduled calibration and verification program for pressure transmitters and gauges against a certified reference, with redundant sensors and automated cross-checking to flag drift before it causes a stop. Replace or recondition sensing elements on a condition- or time-based schedule and log calibration history in the maintenance system.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Number of events: 12.0 occurrences/month · as reported: “Pressure calibration failure”
    Show verbatim quote
    Pressure calibration failure 12 35 4.5
  2. Share of planned time: 4.50 % · as reported: “Pressure calibration failure”
    Show verbatim quote
    Pressure calibration failure 12 35 4.5
  3. Mean event duration: 35.0 min · as reported: “Pressure calibration failure”
    Show verbatim quote
    Pressure calibration failure 12 35 4.5