foratvise
Get Started

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 49 % of the line's lost time. Reported by 1 of the 112 studies that could observe it (sparse evidence).

What happens

Packaged product fails to meet a quality or dimensional specification (such as fill level, weight, seal integrity or pack appearance) because process parameters drift outside their control range; this drift is often most pronounced right after a run begins, before the packaging equipment and upstream process have stabilized, but can also occur during otherwise steady production.

What is done about it

Apply statistical process control to the critical parameters, tighten set points and calibrate sensors/actuators, and define a documented warm-up and stabilization routine at the start of each run so the process reaches target conditions before product is counted as good; route detected non-conforming product to rework or scrap.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.6% [0.1–1.5%]
Expected share of lost time
0.3% [0.1–0.8%]
Share of lost time when present
49% [37–62%]
Studies / units
112 / 155
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.3%]14 studies
  • Soft drinks, bottled water and juices
    0.5% [0.1–1.8%]33 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.2%]14 studies
  • Bakery and pasta
    0.6% [0.1–2.4%]6 studies
  • Meat, poultry and seafood
    0.7% [0.1–2.4%]6 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.4%]4 studies
  • Grain and oilseed milling
    0.7% [0.1–2.4%]4 studies
  • Sugar and confectionery
    0.7% [0.1–2.5%]4 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.1%]8 studies
  • Animal feed and pet food
    0.7% [0.1–2.5%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.9% [0.1–3.3%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Packaged product fails to meet a quality or dimensional specification (such as fill level, weight, seal integrity or pack appearance) because process parameters drift outside their control range; this drift is often most pronounced right after a run begins, before the packaging equipment and upstream process have stabilized, but can also occur during otherwise steady production.

How it looks in SCADA data

Engineering guidance

Checkweigher, vision system or inspection station reject counters rise, with quality alarms flagging parameters outside control limits; reject rate often correlates with a recent machine-state transition from stopped or startup to running, and trend data shows the monitored variable drifting toward or past spec limits before returning to target.

Countermeasure

Engineering guidance

Apply statistical process control to the critical parameters, tighten set points and calibrate sensors/actuators, and define a documented warm-up and stabilization routine at the start of each run so the process reaches target conditions before product is counted as good; route detected non-conforming product to rework or scrap.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 44.2 % · as reported: “Product out of spec at process start of run”
    Show verbatim quote
    Product out of spec at process start of run 44.24% 46.10% 44.58%
  2. Share of lost time: 44.2 % · as reported: “Product out of spec”
    Show verbatim quote
    Product out of spec 44.24% 41.90% 44.17%
  3. Share of lost time: 44.6 % · as reported: “Product out of spec at process start of run”
    Show verbatim quote
    Product out of spec at process start of run 44.24% 46.10% 44.58%
  4. Share of lost time: 44.2 % · as reported: “Product out of spec”
    Show verbatim quote
    Product out of spec 44.24% 41.90% 44.17%