foratvise
Get Started
organizational external

Raw material backlog awaiting processing

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 127 studies that could observe it (sparse evidence).

What happens

A mismatch between the rate at which raw food arrives from suppliers or upstream harvesting and the processing capacity of the line causes material to accumulate faster than it can be handled. This is typically an organisational or scheduling issue rather than an equipment fault, often driven by procurement timing, seasonal supply peaks or poor production planning.

What is done about it

Synchronize raw material intake schedules with actual processing capacity through improved production planning and supplier coordination, and size buffer or cold storage appropriately for expected supply peaks. Where backlogs recur, consider adjusting line throughput, staffing or shift patterns to absorb delivery variability.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.5%]
Expected share of lost time
0.3% [0.1–0.8%]
Share of lost time when present
57% [45–67%]
Studies / units
127 / 161
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.2%]13 studies
  • Soft drinks, bottled water and juices
    0.6% [0.1–1.8%]26 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.1%]11 studies
  • Bakery and pasta
    0.6% [0.1–2.0%]24 studies
  • Meat, poultry and seafood
    0.9% [0.1–3.5%]9 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.4%]7 studies
  • Grain and oilseed milling
    0.6% [0.1–2.4%]6 studies
  • Sugar and confectionery
    0.6% [0.1–2.4%]9 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.4%]5 studies
  • Animal feed and pet food
    0.6% [0.1–2.4%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.2%]10 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

A mismatch between the rate at which raw food arrives from suppliers or upstream harvesting and the processing capacity of the line causes material to accumulate faster than it can be handled. This is typically an organisational or scheduling issue rather than an equipment fault, often driven by procurement timing, seasonal supply peaks or poor production planning.

How it looks in SCADA data

Engineering guidance

SCADA/MES data show rising occupancy or level signals in raw material storage, holding tanks or buffers upstream of the line, together with extended waiting or starved states further downstream once capacity is exceeded. Receipt timestamps diverge increasingly from processing start timestamps, and residence time or queue length metrics trend upward over successive shifts.

Countermeasure

Engineering guidance

Synchronize raw material intake schedules with actual processing capacity through improved production planning and supplier coordination, and size buffer or cold storage appropriately for expected supply peaks. Where backlogs recur, consider adjusting line throughput, staffing or shift patterns to absorb delivery variability.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of loss events: 22.0 % · as reported: “excess stock of raw food awaiting processing”
    Show verbatim quote
    The graph indicates that excess stock of raw food awaiting processing accounts for approximately 22% of total waste, while frequent miscommunication between operators contributes around 20%.