foratvise
Get Started
Setup and adjustments

Reject/discard system adjustment

Setup and adjustmentsAvailabilityLabeling and coding

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 56 % of the line's lost time. Reported by 1 of the 85 studies that could observe it (sparse evidence).

What happens

During changeover or format adjustment, the reject/discard mechanism associated with the labeling station (pushers, air blasts, diverters, sensors) must be mechanically and logically reconfigured or calibrated to match the new container or label geometry before stable production can resume. Until this setting is correctly tuned, the line remains in a non-productive adjustment state.

What is done about it

Standardize changeover procedures with pre-set recipe parameters for each format stored in the control system, use quick-adjust or tool-less mechanisms for the reject guides and sensors, and validate reject function with a short test run before releasing the line to production.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.5%]
Expected share of lost time
0.3% [0.1–0.9%]
Share of lost time when present
56% [44–66%]
Studies / units
85 / 113
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.3%]11 studies
  • Soft drinks, bottled water and juices
    0.8% [0.1–2.4%]29 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.3%]13 studies
  • Bakery and pasta
    0.7% [0.1–2.6%]1 study
  • Meat, poultry and seafood
    0.6% [0.1–2.4%]4 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.4%]4 studies
  • Grain and oilseed milling
    0.7% [0.1–2.5%]3 studies
  • Sugar and confectionery
    0.7% [0.1–2.5%]3 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.4%]4 studies
  • Animal feed and pet food
    0.7% [0.1–2.5%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.4%]9 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During changeover or format adjustment, the reject/discard mechanism associated with the labeling station (pushers, air blasts, diverters, sensors) must be mechanically and logically reconfigured or calibrated to match the new container or label geometry before stable production can resume. Until this setting is correctly tuned, the line remains in a non-productive adjustment state.

How it looks in SCADA data

Engineering guidance

SCADA/MES shows the labeler or reject station in a manual or setup mode state following a changeover event, with repeated sensor triggers, small bursts of rejects without corresponding good-unit counts, and operator acknowledgments of calibration screens. Line speed and output counters remain at zero or near zero while the reject station is being tuned.

Countermeasure

Engineering guidance

Standardize changeover procedures with pre-set recipe parameters for each format stored in the control system, use quick-adjust or tool-less mechanisms for the reject guides and sensors, and validate reject function with a short test run before releasing the line to production.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 3.00 min · as reported: “Adjustment of reject/discard system”
    Show verbatim quote
    Regulagem do descarte 3
  2. Lost time: 3.00 min · as reported: “Adjustment of reject/discard system”
    Show verbatim quote
    Regulagem do descarte 3