foratvise
Get Started
Equipment failure (breakdowns)

Roller arm/liner failure

Equipment failure (breakdowns)AvailabilityMilling and grinding

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 58 % of the line's lost time. Reported by 2 of the 43 studies that could observe it (sparse evidence).

What happens

The roller arm or its mounted roller and liner wear, crack, or work loose under the cyclic loading and friction of the milling process, causing the roller to jam against its mating surface, come loose from the arm, or produce abnormal noise and vibration. Continued operation in this degraded state forces an unplanned stop so the arm, roller, or liner can be repaired or replaced before damage propagates to adjacent drive or frame components.

What is done about it

Implement condition-based inspection of roller arm bushings, fasteners, and liner wear with vibration and noise monitoring, and schedule preventive replacement of liners and arm components before they reach failure thresholds. Standardize torque/clamping procedures for roller-to-arm attachment to prevent loosening in service.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.0% [0.2–3.0%]
Expected share of lost time
0.6% [0.1–1.7%]
Share of lost time when present
58% [47–68%]
Studies / units
43 / 48
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.1% [0.1–4.4%]5 studies
  • Soft drinks, bottled water and juices
    1.2% [0.1–5.0%]1 study
  • Brewing, wine and spirits
    1.2% [0.1–4.9%]0 studies
  • Bakery and pasta
    1.2% [0.1–4.7%]0 studies
  • Meat, poultry and seafood
    1.2% [0.1–4.4%]0 studies
  • Fruit and vegetable processing
    1.1% [0.1–4.2%]2 studies
  • Grain and oilseed milling
    1.1% [0.1–4.1%]7 studies
  • Sugar and confectionery
    1.0% [0.1–3.9%]10 studies
  • Snacks, coffee, tea and other foods
    1.7% [0.2–6.4%]5 studies
  • Animal feed and pet food
    1.1% [0.1–4.2%]6 studies
  • Food manufacturing (unspecified or mixed)
    1.1% [0.1–4.2%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The roller arm or its mounted roller and liner wear, crack, or work loose under the cyclic loading and friction of the milling process, causing the roller to jam against its mating surface, come loose from the arm, or produce abnormal noise and vibration. Continued operation in this degraded state forces an unplanned stop so the arm, roller, or liner can be repaired or replaced before damage propagates to adjacent drive or frame components.

How it looks in SCADA data

Engineering guidance

Equipment-failure stop codes tagged to the roller mill or roller arm asset, often preceded by abnormal vibration or motor-current/torque excursions and operator-logged noise alarms before the stop. Stop duration is consistent with mechanical repair/replacement (parts swap) rather than a brief clearance, and the event recurs on the same roller/arm position across runs.

Countermeasure

Engineering guidance

Implement condition-based inspection of roller arm bushings, fasteners, and liner wear with vibration and noise monitoring, and schedule preventive replacement of liners and arm components before they reach failure thresholds. Standardize torque/clamping procedures for roller-to-arm attachment to prevent loosening in service.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Mean event duration: 3.00 Hr · as reported: “Roller arm failures/Liner replacement”
    Show verbatim quote
    Roller arm failures/Liner replacement 2805.00 3.00 2794.5 13.5
  2. Lost time: 3.00 Hr · as reported: “V1: Roller arm jammed/Roller arm change”
    Show verbatim quote
    08/30/16 016657 V1: Roller arm jammed/Roller arm change CMU 0 3 3
  3. Lost time: 3.00 Hr · as reported: “V1: Roller arm/Liner replacement”
    Show verbatim quote
    01/06/16 014500 V1: Roller arm/Liner replacement CMP 0 3 3
  4. Time between events: 2,795 Hr · as reported: “Roller arm failures/Liner replacement”
    Show verbatim quote
    Roller arm failures/Liner replacement 2805.00 3.00 2794.5 13.5
  5. Mean event duration: 13.5 Hr · as reported: “Roller arm failures/Liner replacement”
    Show verbatim quote
    Roller arm failures/Liner replacement 2805.00 3.00 2794.5 13.5
  6. Time between events: 2,805 Hr · as reported: “Roller arm failures/Liner replacement”
    Show verbatim quote
    Roller arm failures/Liner replacement 2805.00 3.00 2794.5 13.5
  7. Number of events: 1.00 events · as reported: “roller arm failure”
    Show verbatim quote
    V1 had recorded one roller arm failure between 01/12/15 and 31/01/17, and had its grinding liner replaced 2 times in that period.
  8. Lost time: 5.00 Hr · as reported: “V4: Roller arm and liner change”
    Show verbatim quote
    05/07/16 015728 V4: Roller arm and liner change CMP 0 5 5
  9. Lost time: 22.0 Hr · as reported: “V4: Center shaft service/Roller arm & liner change”
    Show verbatim quote
    10/13/16 016972 V4: Center shaft service/Roller arm & liner change CMU 16 6 22
  10. Lost time: 2.25 Hr · as reported: “V4: Roller came loose from arm/Abnormal noise”
    Show verbatim quote
    01/04/17 017546 V4: Roller came loose from arm/Abnormal noise CMU 0 2.25 2.25