foratvise
Get Started
Equipment failure (breakdowns)

Roller arm locker plate bolt failure

Equipment failure (breakdowns)AvailabilityMilling and grinding

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 58 % of the line's lost time. Reported by 1 of the 43 studies that could observe it (sparse evidence).

What happens

The bolt that secures the locker plate holding the roller arm in position is subjected to cyclic mechanical load and vibration during milling, causing it to loosen, fatigue and eventually break or shear, together with associated scrapper or stopper components. Once the bolt fails, the roller arm loses its fixed position and the roll gap or roll pressure can no longer be maintained correctly.

What is done about it

Implement periodic torque-checking and tightening of locker plate bolts as part of preventive maintenance, use bolts with appropriate fatigue rating and locking mechanisms (e.g., thread-locking compound or safety wire), and monitor vibration or roll gap trends to detect loosening before failure occurs.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.9% [0.2–2.6%]
Expected share of lost time
0.5% [0.1–1.5%]
Share of lost time when present
58% [47–68%]
Studies / units
43 / 48
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.1% [0.1–4.0%]5 studies
  • Soft drinks, bottled water and juices
    1.1% [0.1–4.1%]1 study
  • Brewing, wine and spirits
    1.1% [0.1–4.3%]0 studies
  • Bakery and pasta
    1.1% [0.1–4.3%]0 studies
  • Meat, poultry and seafood
    1.1% [0.1–4.2%]0 studies
  • Fruit and vegetable processing
    1.1% [0.1–4.4%]2 studies
  • Grain and oilseed milling
    1.0% [0.1–3.8%]7 studies
  • Sugar and confectionery
    1.0% [0.1–3.7%]10 studies
  • Snacks, coffee, tea and other foods
    1.5% [0.2–5.6%]5 studies
  • Animal feed and pet food
    1.1% [0.1–4.0%]6 studies
  • Food manufacturing (unspecified or mixed)
    1.0% [0.1–3.9%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The bolt that secures the locker plate holding the roller arm in position is subjected to cyclic mechanical load and vibration during milling, causing it to loosen, fatigue and eventually break or shear, together with associated scrapper or stopper components. Once the bolt fails, the roller arm loses its fixed position and the roll gap or roll pressure can no longer be maintained correctly.

How it looks in SCADA data

Engineering guidance

SCADA/MES logs show an unplanned stop event on a specific roller/mill unit tagged with a mechanical fault or bolt/locker plate alarm, often preceded by abnormal vibration, roll gap deviation or motor load fluctuation signals. The stop duration corresponds to a maintenance intervention window with roller arm or component replacement logged in the work order history.

Countermeasure

Engineering guidance

Implement periodic torque-checking and tightening of locker plate bolts as part of preventive maintenance, use bolts with appropriate fatigue rating and locking mechanisms (e.g., thread-locking compound or safety wire), and monitor vibration or roll gap trends to detect loosening before failure occurs.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Time between events: 2,807 Hr · as reported: “Roller arm locker plate bolt/scrapper failure”
    Show verbatim quote
    Roller arm locker plate bolt/scrapper failure 2807.21 0.79 699.70 2.30
  2. Lost time: 1.00 Hr · as reported: “V4: Roller arm locker plate bolt broken”
    Show verbatim quote
    12/08/15 014601 V4: Roller arm locker plate bolt broken CMU 0 1 1
  3. Lost time: 0.580 Hr · as reported: “V1: Roller arm (R63) locker plate bolt broken”
    Show verbatim quote
    03/08/16 015266 V1: Roller arm (R63) locker plate bolt broken CMU 0 0.58 0.58
  4. Lost time: 8.00 Hr · as reported: “V4: Roller arm locker plate bolt broken/Roller arm (R21) change”
    Show verbatim quote
    12/04/15 014523 V4: Roller arm locker plate bolt broken/Roller arm (R21) change CMU 4 4 8
  5. Mean event duration: 0.790 Hr · as reported: “Roller arm locker plate bolt/scrapper failure”
    Show verbatim quote
    Roller arm locker plate bolt/scrapper failure 2807.21 0.79 699.70 2.30
  6. Number of events: 2.00 events · as reported: “roller/scrapper failure”
    Show verbatim quote
    V1 had only recorded 2 failures from operating 351 days.
  7. Lost time: 1.58 Hr · as reported: “roller/scrapper failure”
    Show verbatim quote
    These intermittent stoppages caused by such failure had accumulated 1.58, and 18.41 hour of stoppage time for V1 and V4 respectively.
  8. Time between events: 700 Hr · as reported: “Roller arm locker plate bolt/scrapper failure”
    Show verbatim quote
    Roller arm locker plate bolt/scrapper failure 2807.21 0.79 699.70 2.30
  9. Mean event duration: 2.30 Hr · as reported: “Roller arm locker plate bolt/scrapper failure”
    Show verbatim quote
    Roller arm locker plate bolt/scrapper failure 2807.21 0.79 699.70 2.30
  10. Number of events: 7.00 events · as reported: “roller/scrapper failure”
    Show verbatim quote
    During the same period, V4 had encountered the same failure 5 times extra, totalling a 7 failure.
  11. Lost time: 18.4 Hr · as reported: “roller/scrapper failure”
    Show verbatim quote
    These intermittent stoppages caused by such failure had accumulated 1.58, and 18.41 hour of stoppage time for V1 and V4 respectively.
  12. Share of loss events: 43.8 % · as reported: “locker plate bolt damage”
    Show verbatim quote
    43.75% of failure in V4 mill is caused by locker plate bolt damage, the higher rate of such failure is due to the type of drive employed in V4 mill.
  13. Lost time: 0.330 Hr · as reported: “V4: R49 Locker plate bolt broken”
    Show verbatim quote
    02/19/16 015158 V4: R49 Locker plate bolt broken CMU 0 0.33 0.33
  14. Lost time: 0.500 Hr · as reported: “V4: Roller arm (R49) locker plate bolt broken”
    Show verbatim quote
    03/09/16 015231 V4: Roller arm (R49) locker plate bolt broken CMU 0 0.5 0.5
  15. Lost time: 1.00 Hr · as reported: “V4: Roller arm (R49) locker plate bolt broken”
    Show verbatim quote
    03/29/16 015448 V4: Roller arm (R49) locker plate bolt broken CMU 0 1 1
  16. Lost time: 0.330 Hr · as reported: “V4: R49 locker plate holding bolts loosen”
    Show verbatim quote
    04/06/16 015496 V4: R49 locker plate holding bolts loosen CMU 0 0.33 0.33
  17. Lost time: 5.00 Hr · as reported: “V4: Roller arm locker plate bolt broken/stopper broken”
    Show verbatim quote
    07/01/16 016185 V4: Roller arm locker plate bolt broken/stopper broken CMU 0 5 5