foratvise
Get Started
Reduced speed

Sealing system improperly adjusted

Reduced speedPerformanceCapping and seaming

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 63 % of the line's lost time. Reported by 0 of the 82 studies that could observe it (sparse evidence).

What happens

The sealing station parameters (pressure, temperature, dwell time, alignment) are set outside the optimal operating window, so the machine cannot maintain seal integrity at nominal speed. Operators or control logic compensate by deliberately slowing the line to allow more contact time or pressure per cycle, which keeps seals acceptable but reduces throughput.

What is done about it

Define and lock the optimal sealing parameters by format in the recipe management system, with automated verification against set points at start-up and during the run. Implement operator checklists and periodic calibration of the sealing station, and use seal-quality feedback (vision, leak test, torque) to trigger automatic parameter correction instead of manual speed reduction.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.6% [0.1–1.6%]
Expected share of lost time
0.4% [0.1–1.0%]
Share of lost time when present
63% [50–76%]
Studies / units
82 / 109
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.2%]11 studies
  • Soft drinks, bottled water and juices
    0.6% [0.1–1.9%]26 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.4%]11 studies
  • Bakery and pasta
    0.7% [0.1–2.7%]0 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.3%]7 studies
  • Fruit and vegetable processing
    0.7% [0.1–2.5%]4 studies
  • Grain and oilseed milling
    0.6% [0.1–2.4%]3 studies
  • Sugar and confectionery
    0.7% [0.1–2.5%]3 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.4%]4 studies
  • Animal feed and pet food
    0.6% [0.1–2.5%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.4%]9 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The sealing station parameters (pressure, temperature, dwell time, alignment) are set outside the optimal operating window, so the machine cannot maintain seal integrity at nominal speed. Operators or control logic compensate by deliberately slowing the line to allow more contact time or pressure per cycle, which keeps seals acceptable but reduces throughput.

How it looks in SCADA data

Engineering guidance

SCADA/MES shows the sealing or capping station running below its ideal cycle rate while in a normal production state, with set points for pressure, temperature or dwell time persistently deviating from the recipe target. Seal-quality or torque sensors may show values near the control limit without triggering a fault, and the line speed trend correlates with these deviations rather than with upstream starvation or blocking.

Countermeasure

Engineering guidance

Define and lock the optimal sealing parameters by format in the recipe management system, with automated verification against set points at start-up and during the run. Implement operator checklists and periodic calibration of the sealing station, and use seal-quality feedback (vision, leak test, torque) to trigger automatic parameter correction instead of manual speed reduction.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 46.5 % · as reported: “improper adjustment of the sealing system”
    Show verbatim quote
    Additionally, 46.5% of the low performance was due to improper adjustment of the sealing system, and the presence of defective products was associated with wear on the magazine chain of the primary packaging machine, accounting for 4.3%.