foratvise
Get Started

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 112 studies that could observe it (sparse evidence).

What happens

At the start of a shift the packaging line must be brought from a stopped or standby state to stable operating conditions, requiring warm-up, checks and fine adjustments before good units are produced; at the end of a shift the line is progressively run down, cleared and prepared for the next shift, which also consumes productive time without output. These transition periods occur independently of any product or format change and are tied purely to the shift schedule.

What is done about it

Standardize shift handover and start-up/shut-down procedures with checklists, pre-stage settings and materials before the shift begins, and use brief shift overlap so the line can keep running while responsibilities transfer. Apply quick-setup principles to shorten warm-up and shutdown sequences and track them as a distinct, monitored step in the shift schedule.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.4%]
Expected share of lost time
0.3% [0.1–0.8%]
Share of lost time when present
57% [44–67%]
Studies / units
112 / 155
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.2%]14 studies
  • Soft drinks, bottled water and juices
    0.5% [0.1–1.6%]33 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.0%]14 studies
  • Bakery and pasta
    0.6% [0.1–2.3%]6 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.4%]6 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.3%]4 studies
  • Grain and oilseed milling
    0.6% [0.1–2.2%]4 studies
  • Sugar and confectionery
    0.6% [0.1–2.3%]4 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.1%]8 studies
  • Animal feed and pet food
    0.6% [0.1–2.2%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.9% [0.1–3.2%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

At the start of a shift the packaging line must be brought from a stopped or standby state to stable operating conditions, requiring warm-up, checks and fine adjustments before good units are produced; at the end of a shift the line is progressively run down, cleared and prepared for the next shift, which also consumes productive time without output. These transition periods occur independently of any product or format change and are tied purely to the shift schedule.

How it looks in SCADA data

Engineering guidance

MES/SCADA logs show recurring blocks of setup or non-running machine state aligned with the shift calendar at the start and end of each shift, with no accompanying product-change or recipe-change event. Output counters remain flat or show reduced partial counts during these intervals, and the pattern repeats consistently across shifts rather than correlating with specific SKUs.

Countermeasure

Engineering guidance

Standardize shift handover and start-up/shut-down procedures with checklists, pre-stage settings and materials before the shift begins, and use brief shift overlap so the line can keep running while responsibilities transfer. Apply quick-setup principles to shorten warm-up and shutdown sequences and track them as a distinct, monitored step in the shift schedule.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 3,908 min · as reported: “Initial and end of shift setup”
    Show verbatim quote
    Setting awal dan akhir shift 3,908 35%