foratvise
Get Started
Idling and minor stops (micro-stops)

Stamp/cap jam on applicator track

Idling and minor stops (micro-stops)PerformanceFilling

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 53 % of the line's lost time. Reported by 1 of the 120 studies that could observe it (sparse evidence).

What happens

A stamp or cap being fed along the guide track of the applicator becomes misaligned, tilted or wedged due to minor dimensional variation, static buildup, debris or worn guide rails, blocking the path for following pieces. The applicator or escapement cannot advance the next piece until the jammed item is cleared, halting the feed without any component breakage.

What is done about it

Inspect and adjust track guide clearances, deburr or polish wear points, and add anti-static or lubrication treatment suited to the stamp/cap material to reduce sticking. Implement sensor-triggered automatic clearing or operator alert with a quick-access door, and schedule periodic cleaning and alignment checks of the track as preventive maintenance.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.4%]
Expected share of lost time
0.3% [0.1–0.7%]
Share of lost time when present
53% [41–65%]
Studies / units
120 / 162
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–1.9%]18 studies
  • Soft drinks, bottled water and juices
    0.6% [0.1–2.0%]44 studies
  • Brewing, wine and spirits
    0.5% [0.1–1.9%]16 studies
  • Bakery and pasta
    0.6% [0.1–2.3%]0 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.2%]6 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.2%]4 studies
  • Grain and oilseed milling
    0.6% [0.1–2.2%]6 studies
  • Sugar and confectionery
    0.6% [0.1–2.3%]3 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.1%]6 studies
  • Animal feed and pet food
    0.6% [0.1–2.3%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.2%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

A stamp or cap being fed along the guide track of the applicator becomes misaligned, tilted or wedged due to minor dimensional variation, static buildup, debris or worn guide rails, blocking the path for following pieces. The applicator or escapement cannot advance the next piece until the jammed item is cleared, halting the feed without any component breakage.

How it looks in SCADA data

Engineering guidance

Short machine-state transition to stopped or fault state with a jam or feed-fault alarm tied to the stamp/cap track sensor, typically cleared manually within a brief interval; downstream filling heads show starvation while the infeed accumulates. Stop counters for this station rise without any corresponding maintenance work order, and the event repeats in bursts rather than as isolated incidents.

Countermeasure

Engineering guidance

Inspect and adjust track guide clearances, deburr or polish wear points, and add anti-static or lubrication treatment suited to the stamp/cap material to reduce sticking. Implement sensor-triggered automatic clearing or operator alert with a quick-access door, and schedule periodic cleaning and alignment checks of the track as preventive maintenance.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 484 min · as reported: “stuck stamp on track”
    Show verbatim quote
    In the month February – May 2019 recorded existence minor idling downtime stop at line 4 , namely , CIP ( Cleaning In Place ) 2,509 minutes , SIP ( Sanitation In Place ) 1,943 minutes , stuck stamp on track 484 minutes , bottle stuck in the SIPA 322 divider , tilting was stuck for 277 minutes and the pallet ran out for 93 minutes .