Minor stoppages on sterilizer
In short
It appears in about 1 of every 100 lines studied.
When it appears, it takes on average about 53 % of the line's lost time. Reported by 1 of the 34 studies that could observe it (sparse evidence).
What happens
Short interruptions occur on the sterilizer (retort or UHT line) when containers or carriers jam at infeed/outfeed, sensors are momentarily blocked, or chains and conveyors hang up during loading and unloading of the sterilization cycle. These stoppages are cleared by the operator on the spot without any maintenance intervention and do not involve a mechanical or electrical failure.
What is done about it
Standard countermeasures include improving container/carrier guiding and alignment at infeed and outfeed, adjusting sensor sensitivity and positioning to avoid false blocking, and reviewing accumulation buffers to reduce jam frequency. Operator training on fast, safe clearing procedures and periodic review of minor-stop logs to target recurring trouble spots are also typical.
Practical guidance written from engineering knowledge; it is not a statistical estimate.
1Probability and evidence
- Probability of presence
- 0.9% [0.1–2.9%]
- Expected share of lost time
- 0.5% [0.1–1.5%]
- Share of lost time when present
- 53% [40–65%]
- Studies / units
- 34 / 37
- Evidence grade
- D
Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.
2Probability by segment
- Dairy products1.1% [0.1–4.4%]5 studies
- Soft drinks, bottled water and juices1.1% [0.1–4.2%]2 studies
- Brewing, wine and spirits1.1% [0.1–4.5%]1 study
- Bakery and pasta1.1% [0.1–4.5%]0 studies
- Meat, poultry and seafood1.1% [0.1–4.4%]1 study
- Fruit and vegetable processing1.1% [0.1–4.5%]2 studies
- Grain and oilseed milling1.6% [0.1–6.4%]6 studies
- Sugar and confectionery1.1% [0.1–4.3%]3 studies
- Snacks, coffee, tea and other foods1.1% [0.1–4.4%]3 studies
- Animal feed and pet food1.1% [0.1–4.6%]4 studies
- Food manufacturing (unspecified or mixed)1.0% [0.1–4.1%]7 studies
3Mechanism, SCADA signature and countermeasure
Mechanism
Engineering guidanceShort interruptions occur on the sterilizer (retort or UHT line) when containers or carriers jam at infeed/outfeed, sensors are momentarily blocked, or chains and conveyors hang up during loading and unloading of the sterilization cycle. These stoppages are cleared by the operator on the spot without any maintenance intervention and do not involve a mechanical or electrical failure.
How it looks in SCADA data
Engineering guidanceMES/SCADA logs show a high number of brief machine-state transitions to stopped or fault-reset states with very short durations, often clustered around infeed/outfeed sensors or carrier/chain position signals, interspersed with normal running states. Upstream or downstream equipment may show short starvation or blocking periods correlated with these events, but no work order or maintenance alarm is generated.
Countermeasure
Engineering guidanceStandard countermeasures include improving container/carrier guiding and alignment at infeed and outfeed, adjusting sensor sensitivity and positioning to avoid false blocking, and reviewing accumulation buffers to reduce jam frequency. Operator training on fast, safe clearing procedures and periodic review of minor-stop logs to target recurring trouble spots are also typical.
4Sources
- Analisa Perawatan Mesin Sterilizer Menggunakan Metode Overall Equipment Effectivenees (OEE) Pada PT. Djaja Putra Indonesia Kabupaten Asahan (2020)Open sourceShare of lost time: 25.2 % · as reported: “Idling minor Stoppages”
Show verbatim quote
Faktor terbesar yang mempengaruhi efektifitas mesin Sterilizer dan menjadi prioritas untuk dieleminasi adalah faktor Equipment Failures sebesar 61,54% dan faktor Idling minor Stoppages sebesar 25,15%.
- ANALISA PERHITUNGAN OVERALL EQUIPMENT EFFECTIVENESS (OEE) PADA PROSES AWAL PENGOLAHAN KELAPA SAWIT DI PT. PERKEBUNAN NUSANTARA IV GUNUNG BAYU (2019)Open sourceShare of lost time: 0 % · as reported: “Idling And Minor Stoppages”
Show verbatim quote
Idling And Minor Stoppages by 0% and Rework Loss by 0%

