foratvise
Get Started
Process defects (scrap and rework)

Thermal variability during tempering affecting fill accuracy

Process defects (scrap and rework)QualityFilling

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 0 of the 120 studies that could observe it (sparse evidence).

What happens

Unstable temperature control during the tempering stage changes the product's viscosity and crystallization state, so the fluid does not behave consistently when it reaches the filling station. This variability translates into dosing inaccuracies, producing underfilled or overfilled units outside specification.

What is done about it

Tighten closed-loop temperature control in the tempering unit (improved PID tuning, better heat exchanger response, insulation) to keep the product within its target thermal and viscosity window. Complement this with periodic recalibration of filling pumps or valves so dosing accuracy is maintained despite minor residual viscosity changes.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.1%]
Expected share of lost time
0.2% [0.0–0.5%]
Share of lost time when present
48% [36–60%]
Studies / units
120 / 162
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.7%]18 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.3%]44 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.5%]16 studies
  • Bakery and pasta
    0.4% [0.0–1.7%]0 studies
  • Meat, poultry and seafood
    0.4% [0.0–1.7%]6 studies
  • Fruit and vegetable processing
    0.4% [0.0–1.7%]4 studies
  • Grain and oilseed milling
    0.4% [0.0–1.7%]6 studies
  • Sugar and confectionery
    0.5% [0.0–1.8%]3 studies
  • Snacks, coffee, tea and other foods
    0.4% [0.0–1.6%]6 studies
  • Animal feed and pet food
    0.4% [0.0–1.7%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.4% [0.0–1.7%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Unstable temperature control during the tempering stage changes the product's viscosity and crystallization state, so the fluid does not behave consistently when it reaches the filling station. This variability translates into dosing inaccuracies, producing underfilled or overfilled units outside specification.

How it looks in SCADA data

Engineering guidance

Temperature trends in the tempering circuit drift or oscillate outside the controlled band, often preceding periods where fill weight or fill volume readings at the filler show increased dispersion or bias relative to target. Correlation analysis typically links tempering temperature excursions with downstream checkweigher or flow-meter deviation alarms.

Countermeasure

Engineering guidance

Tighten closed-loop temperature control in the tempering unit (improved PID tuning, better heat exchanger response, insulation) to keep the product within its target thermal and viscosity window. Complement this with periodic recalibration of filling pumps or valves so dosing accuracy is maintained despite minor residual viscosity changes.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Defect rate: 25.0 % · as reported: “thermal variability during tempering, inaccurate filling”
    Show verbatim quote
    Reprocessing overall | 25%
  2. Defect rate: 5.00 % · as reported: “reduced thermal variability, improved filling control”
    Show verbatim quote
    Reprocessing overall | 5%