foratvise
Get Started
Equipment failure (breakdowns)

Timing belt misalignment or failure

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 112 studies that could observe it (sparse evidence).

What happens

The timing belt that synchronizes motion between packaging mechanisms loses correct tension, fit or alignment due to wear, stretching or incorrect installation, causing it to slip, skip teeth or eventually snap. This desynchronizes the moving parts it drives, leading to mistimed transfers, collisions or complete loss of motion until the belt is replaced or readjusted.

What is done about it

Implement scheduled inspection and replacement of timing belts based on condition (tension, wear, cracking) as part of preventive maintenance, and ensure correct belt specification, fit and tensioning procedures during installation. Use belt-tension monitoring or vibration analysis to detect degradation before failure.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.6% [0.1–1.6%]
Expected share of lost time
0.3% [0.1–0.9%]
Share of lost time when present
57% [46–68%]
Studies / units
112 / 155
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.7% [0.1–2.5%]14 studies
  • Soft drinks, bottled water and juices
    0.6% [0.1–1.9%]33 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.2%]14 studies
  • Bakery and pasta
    0.7% [0.1–2.6%]6 studies
  • Meat, poultry and seafood
    0.7% [0.1–2.5%]6 studies
  • Fruit and vegetable processing
    0.7% [0.1–2.6%]4 studies
  • Grain and oilseed milling
    0.7% [0.1–2.8%]4 studies
  • Sugar and confectionery
    0.7% [0.1–2.6%]4 studies
  • Snacks, coffee, tea and other foods
    0.7% [0.1–2.5%]8 studies
  • Animal feed and pet food
    0.7% [0.1–2.5%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.9% [0.1–3.2%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The timing belt that synchronizes motion between packaging mechanisms loses correct tension, fit or alignment due to wear, stretching or incorrect installation, causing it to slip, skip teeth or eventually snap. This desynchronizes the moving parts it drives, leading to mistimed transfers, collisions or complete loss of motion until the belt is replaced or readjusted.

How it looks in SCADA data

Engineering guidance

Equipment fault or jam alarms correlate with drive-axis position or encoder mismatch between synchronized mechanisms, and motor torque or current shows irregular spikes or drops. Machine state logs show unplanned stop events requiring maintenance intervention, often preceded by intermittent minor stoppages as belt condition degrades.

Countermeasure

Engineering guidance

Implement scheduled inspection and replacement of timing belts based on condition (tension, wear, cracking) as part of preventive maintenance, and ensure correct belt specification, fit and tensioning procedures during installation. Use belt-tension monitoring or vibration analysis to detect degradation before failure.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Number of events: 1,171 occurrences · as reported: “imprecise timing belts, improper timing belt fit, and broken timing belts”
    Show verbatim quote
    These issues contribute to downtime with a total of 5663 minutes and a frequency of 1171 occurrences.
  2. Lost time: 5,663 minutes · as reported: “imprecise timing belts, improper timing belt fit, and broken timing belts”
    Show verbatim quote
    These issues contribute to downtime with a total of 5663 minutes and a frequency of 1171 occurrences.