foratvise
Get Started
Process defects (scrap and rework)

Underfill (low fill weight/volume)

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 0 of the 112 studies that could observe it (sparse evidence).

What happens

Dosing or filling mechanisms deliver less product than the target fill level or weight because of worn valves or nozzles, inaccurate volumetric or gravimetric metering, foam or air entrainment, viscosity changes, or drift in level/weight control settings. The resulting packages fall below the specified fill tolerance and are identified as nonconforming at first pass.

What is done about it

Recalibrate and verify filling heads, dosing pumps or scales against reference standards, and replace worn nozzles, valves or seals that cause inconsistent delivery. Implement closed-loop feedback from checkweighers to automatically correct fill setpoints and schedule preventive verification of metering components.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.1%]
Expected share of lost time
0.2% [0.0–0.5%]
Share of lost time when present
48% [36–60%]
Studies / units
112 / 155
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.7%]14 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.4%]33 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.7%]14 studies
  • Bakery and pasta
    0.5% [0.0–1.8%]6 studies
  • Meat, poultry and seafood
    0.4% [0.0–1.8%]6 studies
  • Fruit and vegetable processing
    0.5% [0.0–1.8%]4 studies
  • Grain and oilseed milling
    0.4% [0.0–1.7%]4 studies
  • Sugar and confectionery
    0.5% [0.0–1.7%]4 studies
  • Snacks, coffee, tea and other foods
    0.4% [0.0–1.7%]8 studies
  • Animal feed and pet food
    0.4% [0.0–1.7%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.4% [0.0–1.7%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Dosing or filling mechanisms deliver less product than the target fill level or weight because of worn valves or nozzles, inaccurate volumetric or gravimetric metering, foam or air entrainment, viscosity changes, or drift in level/weight control settings. The resulting packages fall below the specified fill tolerance and are identified as nonconforming at first pass.

How it looks in SCADA data

Engineering guidance

Checkweigher or fill-level sensors report readings trending below the target setpoint, with an increase in low-fill reject counts and tighter correlation to specific filling heads or valves. MES quality logs show a rising rate of underfill nonconformities without corresponding downtime events, since the line continues running at normal speed.

Countermeasure

Engineering guidance

Recalibrate and verify filling heads, dosing pumps or scales against reference standards, and replace worn nozzles, valves or seals that cause inconsistent delivery. Implement closed-loop feedback from checkweighers to automatically correct fill setpoints and schedule preventive verification of metering components.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Number of events: 58.0 kasus · as reported: “Underfill”
    Show verbatim quote
    Underfill 58 0,22 1,27
  2. Share of loss events: 1.27 % · as reported: “Underfill”
    Show verbatim quote
    Underfill 58 0,22 1,27
  3. Defect rate: 0.220 % · as reported: “Underfill”
    Show verbatim quote
    Underfill 58 0,22 1,27