foratvise
Get Started
not classifiable

Unspecified equipment failure or adjustment stop

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 0 of the 127 studies that could observe it (sparse evidence).

What happens

The line or a piece of equipment stops for a reason reported only generically as a failure or an adjustment, without the primary study distinguishing whether the loss of function required a repair, a parameter correction, or a changeover-type intervention. The underlying physical mechanism (mechanical wear, control fault, sensor misalignment, format change, etc.) is not disclosed in the source report.

What is done about it

Improve downtime event classification at the source so that failure events and adjustment events are logged under separate, specific reason codes, enabling root-cause analysis and targeted corrective or preventive actions once the true nature of the stop is known.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.1%]
Expected share of lost time
0.2% [0.0–0.6%]
Share of lost time when present
57% [45–68%]
Studies / units
127 / 161
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.7%]13 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.5%]26 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.7%]11 studies
  • Bakery and pasta
    0.4% [0.0–1.5%]24 studies
  • Meat, poultry and seafood
    0.4% [0.0–1.6%]9 studies
  • Fruit and vegetable processing
    0.4% [0.0–1.7%]7 studies
  • Grain and oilseed milling
    0.4% [0.0–1.7%]6 studies
  • Sugar and confectionery
    0.4% [0.0–1.6%]9 studies
  • Snacks, coffee, tea and other foods
    0.4% [0.0–1.7%]5 studies
  • Animal feed and pet food
    0.4% [0.0–1.7%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.4% [0.0–1.7%]10 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The line or a piece of equipment stops for a reason reported only generically as a failure or an adjustment, without the primary study distinguishing whether the loss of function required a repair, a parameter correction, or a changeover-type intervention. The underlying physical mechanism (mechanical wear, control fault, sensor misalignment, format change, etc.) is not disclosed in the source report.

How it looks in SCADA data

Engineering guidance

SCADA/MES logs show a stopped or non-running machine state attributed to a generic downtime code that mixes failure and adjustment reasons, often without a specific fault alarm or component tag, making it indistinguishable from other unplanned or semi-planned stops in the event history.

Countermeasure

Engineering guidance

Improve downtime event classification at the source so that failure events and adjustment events are logged under separate, specific reason codes, enabling root-cause analysis and targeted corrective or preventive actions once the true nature of the stop is known.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 117 h · as reported: “failures or adjustments”
    Show verbatim quote
    The total number of failures or adjustments of all machines was 117 h, of which 23.93% were failures or adjustments of the packaging machine.