foratvise
Get Started
not classifiable

Reduced speed and minor stoppages (unspecified)

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 56 % of the line's lost time. Reported by 1 of the 127 studies that could observe it (sparse evidence).

What happens

The report groups together periods of below-target running speed and short, operator-cleared interruptions without distinguishing between the two, so the underlying physical cause (mechanical drag, minor jams, sensor faults, material flow irregularities, or operator-paced adjustments) cannot be isolated from the label alone. Such generic entries typically arise when the line is affected by several small, recurring frictions that were not individually logged or categorized by the original study.

What is done about it

Introduce finer-grained event logging (automatic stop/speed-state capture with reason codes) so that speed losses and minor stoppages are recorded and timestamped separately, enabling Pareto analysis to identify the dominant recurring frictions. Once disaggregated, apply targeted countermeasures such as autonomous maintenance, sensor recalibration, or flow-path adjustments to the specific causes that emerge.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.5%]
Expected share of lost time
0.3% [0.1–0.8%]
Share of lost time when present
56% [44–67%]
Studies / units
127 / 161
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.3%]13 studies
  • Soft drinks, bottled water and juices
    0.6% [0.1–1.9%]26 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.3%]11 studies
  • Bakery and pasta
    0.6% [0.1–2.1%]24 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.2%]9 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.4%]7 studies
  • Grain and oilseed milling
    0.6% [0.1–2.4%]6 studies
  • Sugar and confectionery
    0.9% [0.1–3.6%]9 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.3%]5 studies
  • Animal feed and pet food
    0.6% [0.1–2.4%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.4%]10 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The report groups together periods of below-target running speed and short, operator-cleared interruptions without distinguishing between the two, so the underlying physical cause (mechanical drag, minor jams, sensor faults, material flow irregularities, or operator-paced adjustments) cannot be isolated from the label alone. Such generic entries typically arise when the line is affected by several small, recurring frictions that were not individually logged or categorized by the original study.

How it looks in SCADA data

Engineering guidance

SCADA/MES data show an alternating pattern of running states at below-nominal rate interspersed with short downtime events, without a dominant fault code or consistent machine-state signature; aggregate OEE reports often lump this time under a single generic non-value-added bucket. No single sensor or alarm correlates strongly with the loss, making root-cause attribution difficult from the trend data alone.

Countermeasure

Engineering guidance

Introduce finer-grained event logging (automatic stop/speed-state capture with reason codes) so that speed losses and minor stoppages are recorded and timestamped separately, enabling Pareto analysis to identify the dominant recurring frictions. Once disaggregated, apply targeted countermeasures such as autonomous maintenance, sensor recalibration, or flow-path adjustments to the specific causes that emerge.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 13.7 % · as reported: “reduced speed and minor stoppage”
    Show verbatim quote
    Analysis showed the distribution of the losses with set-up and failures being the predominant with 66.4% of total lost time, followed by defects participating with 19.9% and reduced speed and minor stoppage contributing with 13.7%.