foratvise
Get Started
Setup and adjustments

Changeover delay due to searching for and fetching tools/utensils

Setup and adjustmentsAvailabilityWhole line or unspecified equipment

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 127 studies that could observe it (sparse evidence).

What happens

During a changeover the operator discovers that the tools, spare parts or utensils needed are not at the workstation and must walk to a storeroom or another area to find and bring them back, adding non-productive time before the line can be reassembled and restarted. This typically happens when there is no standardized kit or shadow board for the format being set up and tool location is not controlled.

What is done about it

Apply SMED principles: pre-stage a dedicated changeover kit or shadow board with every tool and utensil needed for each format at the point of use, and separate internal from external setup activities so retrieval happens before the line stops. Assign a changeover checklist and, where volume justifies it, a dedicated setup technician to eliminate walking and searching time.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.3%]
Expected share of lost time
0.3% [0.1–0.8%]
Share of lost time when present
57% [45–67%]
Studies / units
127 / 161
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.1%]13 studies
  • Soft drinks, bottled water and juices
    0.5% [0.1–1.8%]26 studies
  • Brewing, wine and spirits
    0.6% [0.1–1.9%]11 studies
  • Bakery and pasta
    0.5% [0.1–1.8%]24 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.0%]9 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.0%]7 studies
  • Grain and oilseed milling
    0.6% [0.1–2.2%]6 studies
  • Sugar and confectionery
    0.6% [0.1–2.0%]9 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.0%]5 studies
  • Animal feed and pet food
    0.9% [0.1–3.3%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.1%]10 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During a changeover the operator discovers that the tools, spare parts or utensils needed are not at the workstation and must walk to a storeroom or another area to find and bring them back, adding non-productive time before the line can be reassembled and restarted. This typically happens when there is no standardized kit or shadow board for the format being set up and tool location is not controlled.

How it looks in SCADA data

Engineering guidance

The equipment state log shows an extended changeover/setup state with no machine motion or energy consumption, often with the operator badge or HMI left idle, and the gap does not correlate with any mechanical adjustment step recorded elsewhere on the line. MES changeover timers exceed the standard changeover duration without any fault or jam code being raised.

Countermeasure

Engineering guidance

Apply SMED principles: pre-stage a dedicated changeover kit or shadow board with every tool and utensil needed for each format at the point of use, and separate internal from external setup activities so retrieval happens before the line stops. Assign a changeover checklist and, where volume justifies it, a dedicated setup technician to eliminate walking and searching time.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Mean event duration: 2.81 min · as reported: “Search and transfer utensils to the area”
    Show verbatim quote
    Search and transfer utensils to the area 2.81 Internal External
  2. Lost time: 2.81 min · as reported: “Search and transfer utensils to the area”
    Show verbatim quote
    Search and transfer utensils to the area 2.81