foratvise
Loslegen
Anlagenausfall (Störungen)

Packaging machine breakdown

Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.

Kurz gefasst

Sie tritt bei etwa 4 von 100 untersuchten Linien auf.

Wenn sie auftritt, entfällt auf sie im Mittel etwa 58 % der Verlustzeit der Linie. Berichtet von 15 der 112 Studien, die sie beobachten konnten (starke Evidenz).

Was passiert

A mechanical, electrical, pneumatic or control component of the packer, case packer or wrapping/casing equipment degrades or fails outright (worn parts, broken drive elements, sensor or actuator faults), interrupting the packaging function until a technician repairs or replaces it. Because the fault requires maintenance intervention rather than a simple operator reset, the stop is classified as a breakdown rather than a minor stop.

Was man dagegen tut

Implement condition-based and preventive maintenance on drives, bearings, seals and sensors of the packaging line, with vibration or wear monitoring to anticipate failure. Maintain critical spare parts on site, standardize fast fault-diagnosis and repair procedures, and perform root-cause analysis on recurring breakdowns to redesign weak components.

Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.

1Wahrscheinlichkeit und Evidenz

Gepoolt über alle Segmente. Ein breites Intervall ist ein Ergebnis: Es zeigt, wie viel die Evidenz zu wissen erlaubt.
Auftretenswahrscheinlichkeit
4,4 % [1,9–8,4 %]
Erwarteter Anteil an der Verlustzeit
2,6 % [1,1–4,8 %]
Anteil an der Verlustzeit bei Auftreten
58 % [49–66 %]
Studien / Einheiten
112 / 155
Evidenzgrad
A

Grad A: 10 oder mehr Studien und 10 oder mehr verschiedene Linien, mit einem 95-%-Glaubwürdigkeitsintervall schmaler als 0,20.

2Wahrscheinlichkeit nach Segment

Partiell gepoolte Schätzungen für jedes Branchensegment.
  • Milchprodukte
    3,8 % [0,8–9,9 %]14 Studien
  • Erfrischungsgetränke, abgefülltes Wasser und Säfte
    4,0 % [1,2–8,3 %]33 Studien
  • Bier, Wein und Spirituosen
    7,7 % [2,3–17,2 %]14 Studien
  • Backwaren und Teigwaren
    6,2 % [1,4–16,9 %]6 Studien
  • Fleisch, Geflügel und Fisch
    6,1 % [1,3–16,1 %]6 Studien
  • Obst- und Gemüseverarbeitung
    4,6 % [0,9–12,9 %]4 Studien
  • Getreide- und Ölsaatenmüllerei
    6,4 % [1,3–17,9 %]4 Studien
  • Zucker und Süßwaren
    4,6 % [0,9–13,1 %]4 Studien
  • Snacks, Kaffee, Tee und sonstige Lebensmittel
    5,3 % [1,3–13,3 %]8 Studien
  • Futtermittel und Heimtiernahrung
    4,5 % [0,8–12,1 %]5 Studien
  • Lebensmittelherstellung (nicht spezifiziert oder gemischt)
    8,1 % [2,4–18,1 %]14 Studien

3Mechanismus, SCADA-Signatur und Gegenmaßnahme

Ingenieurpraktische Hinweise, um die Ursache zu erkennen und zu beheben; nicht Teil der statistischen Schätzung.

Mechanismus

Ingenieurpraktische Hinweise

A mechanical, electrical, pneumatic or control component of the packer, case packer or wrapping/casing equipment degrades or fails outright (worn parts, broken drive elements, sensor or actuator faults), interrupting the packaging function until a technician repairs or replaces it. Because the fault requires maintenance intervention rather than a simple operator reset, the stop is classified as a breakdown rather than a minor stop.

So zeigt sie sich in SCADA-Daten

Ingenieurpraktische Hinweise

Machine state transitions from running to fault/down with the stop duration typically exceeding the minor-stop threshold, accompanied by a specific fault or alarm code from the packer's PLC (drive overload, sensor fault, safety interlock). The downtime counter for the packaging asset accumulates against an equipment-failure reason code, while upstream accumulation conveyors fill and downstream conveyors starve, visible as blocked/starved states on neighboring machines.

Gegenmaßnahme

Ingenieurpraktische Hinweise

Implement condition-based and preventive maintenance on drives, bearings, seals and sensors of the packaging line, with vibration or wear monitoring to anticipate failure. Maintain critical spare parts on site, standardize fast fault-diagnosis and repair procedures, and perform root-cause analysis on recurring breakdowns to redesign weak components.

4Quellen

Jeder extrahierte Datenpunkt mit Studie, Wert und wörtlichem Zitat.
  1. Verlustzeit: 155 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 154.5 117.66 158.3 264.5 128.6
  2. Verlustzeit: 118 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 154.5 117.66 158.3 264.5 128.6
  3. Verlustzeit: 158 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 154.5 117.66 158.3 264.5 128.6
  4. Verlustzeit: 265 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 154.5 117.66 158.3 264.5 128.6
  5. Verlustzeit: 129 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 154.5 117.66 158.3 264.5 128.6
  6. Verlustzeit: 322 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 321.5 165.8 285.5 364.3 216
  7. Verlustzeit: 166 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 321.5 165.8 285.5 364.3 216
  8. Verlustzeit: 286 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 321.5 165.8 285.5 364.3 216
  9. Verlustzeit: 364 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 321.5 165.8 285.5 364.3 216
  10. Verlustzeit: 216 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 321.5 165.8 285.5 364.3 216
  11. Verlustzeit: 216 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 321.5 165.8 285.5 364.3 216
  12. Verlustzeit: 322 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 321.5 165.8 285.5 364.3 216
  13. Verlustzeit: 158 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 154.5 117.66 158.3 264.5 128.6
  14. Verlustzeit: 155 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 154.5 117.66 158.3 264.5 128.6
  15. Verlustzeit: 364 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 321.5 165.8 285.5 364.3 216
  16. Verlustzeit: 129 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 154.5 117.66 158.3 264.5 128.6
  17. Verlustzeit: 286 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 321.5 165.8 285.5 364.3 216
  18. Verlustzeit: 166 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 321.5 165.8 285.5 364.3 216
  19. Verlustzeit: 265 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 154.5 117.66 158.3 264.5 128.6
  20. Verlustzeit: 118 h · laut Bericht: “breakdown”
    Wörtliches Zitat anzeigen
    Total number hours of breakdown per year(hours) 154.5 117.66 158.3 264.5 128.6
  21. Verlustzeit: 2.255 min · laut Bericht: “Breakdown”
    Wörtliches Zitat anzeigen
    Breakdown 2,255 56%
  22. Verlustzeit: 1.498 min · laut Bericht: “Setup after breakdown”
    Wörtliches Zitat anzeigen
    Setting setelah breakdown 1,498 100%
  23. Verlustzeit: 6.105 menit · laut Bericht: “Breakdown”
    Wörtliches Zitat anzeigen
    Total 6105 129243 61,33
  24. Anteil an der geplanten Zeit: 5,72 % · laut Bericht: “Breakdown”
    Wörtliches Zitat anzeigen
    Rata-rata 469,62 941,77 5,72
  25. Anteil an der Verlustzeit: 6,00 % · laut Bericht: “automation failures”
    Wörtliches Zitat anzeigen
    A deeper analysis of non-scheduled maintenance data (Figure 9) shows that major causes of packing equipment failure are related to: electrical failures (26%), unscheduled operational (26%) or mechanical (23%) adjustments, worn parts or equipment breakdown (13%) and automation failures (6%).
  26. Anteil an der Verlustzeit: 13,0 % · laut Bericht: “worn parts or equipment breakdown”
    Wörtliches Zitat anzeigen
    A deeper analysis of non-scheduled maintenance data (Figure 9) shows that major causes of packing equipment failure are related to: electrical failures (26%), unscheduled operational (26%) or mechanical (23%) adjustments, worn parts or equipment breakdown (13%) and automation failures (6%).
  27. Anteil an der Verlustzeit: 26,0 % · laut Bericht: “electrical failures”
    Wörtliches Zitat anzeigen
    A deeper analysis of non-scheduled maintenance data (Figure 9) shows that major causes of packing equipment failure are related to: electrical failures (26%), unscheduled operational (26%) or mechanical (23%) adjustments, worn parts or equipment breakdown (13%) and automation failures (6%).
  28. Anteil an der Verlustzeit: 22,0 % · laut Bericht: “packaging failure”
    Wörtliches Zitat anzeigen
    Major Availability losses were categorized as: non-scheduled maintenance (29,010 min. - 58% of Availability losses); packaging failure (11,079 min. - 22%); lack of demand that are downstream losses (8,260 min. - 13%) and; lack of product input to the packing line (952 min. – 2%).
  29. Verlustzeit: 11.079 min · laut Bericht: “packaging failure”
    Wörtliches Zitat anzeigen
    Major Availability losses were categorized as: non-scheduled maintenance (29,010 min. - 58% of Availability losses); packaging failure (11,079 min. - 22%); lack of demand that are downstream losses (8,260 min. - 13%) and; lack of product input to the packing line (952 min. – 2%).
  30. Verlustzeit: 220 min · laut Bericht: “PM2”
    Wörtliches Zitat anzeigen
    Total 2540 485 500 560 450 265 225 240 220 5485 224940 2.44%
  31. Verlustzeit: 225 min · laut Bericht: “PM1”
    Wörtliches Zitat anzeigen
    Total 2540 485 500 560 450 265 225 240 220 5485 224940 2.44%
  32. Anzahl der Ereignisse: 11,0 events · laut Bericht: “PM1”
    Wörtliches Zitat anzeigen
    Total 61 21 24 22 17 7 11 10 8 181
  33. Anzahl der Ereignisse: 8,00 events · laut Bericht: “PM2”
    Wörtliches Zitat anzeigen
    Total 61 21 24 22 17 7 11 10 8 181
  34. Anteil an der Verlustzeit: 0,450 % · laut Bericht: “Breakdown”
    Wörtliches Zitat anzeigen
    Breakdown 0.45% 0.94% 0.38%
  35. Anteil an der Verlustzeit: 0,380 % · laut Bericht: “Breakdown”
    Wörtliches Zitat anzeigen
    Breakdown 0.45% 0.94% 0.38%
  36. Anteil an der geplanten Zeit: 1,27 % · laut Bericht: “Breakdown”
    Wörtliches Zitat anzeigen
    4 Breakdown 1,27 4,04 98,66
  37. Anteil an der Verlustzeit: 4,04 % · laut Bericht: “Breakdown”
    Wörtliches Zitat anzeigen
    4 Breakdown 1,27 4,04 98,66
  38. Verlustzeit: 13.590 min · laut Bericht: “fallas”
    Wörtliches Zitat anzeigen
    el tiempo total disponible fue de 71 588 minutos, con un tiempo de parada acumulado de 13 590 minutos y un total de 249 fallas.
  39. Anzahl der Ereignisse: 249 events · laut Bericht: “fallas”
    Wörtliches Zitat anzeigen
    el tiempo total disponible fue de 71 588 minutos, con un tiempo de parada acumulado de 13 590 minutos y un total de 249 fallas.
  40. Zeit zwischen Ereignissen: 233 min · laut Bericht: “fallas”
    Wörtliches Zitat anzeigen
    El MTBF promedio durante este período fue de 232.92 minutos, mientras que el MTTR fue de 54.58 minutos.
  41. Mittlere Ereignisdauer: 54,6 min · laut Bericht: “fallas”
    Wörtliches Zitat anzeigen
    El MTBF promedio durante este período fue de 232.92 minutos, mientras que el MTTR fue de 54.58 minutos.
  42. Verlustzeit: 5.671 min · laut Bericht: “fallas”
    Wörtliches Zitat anzeigen
    mostrando que el tiempo disponible fue de 47 290 minutos con un tiempo de parada de 5671 minutos y 110 fallas
  43. Anzahl der Ereignisse: 110 events · laut Bericht: “fallas”
    Wörtliches Zitat anzeigen
    mostrando que el tiempo disponible fue de 47 290 minutos con un tiempo de parada de 5671 minutos y 110 fallas
  44. Zeit zwischen Ereignissen: 378 min · laut Bericht: “fallas”
    Wörtliches Zitat anzeigen
    obteniendo un MTBF promedio de 378.36 minutos (Visualizar Fig. 7), un MTTR promedio de 51.55 minutos
  45. Mittlere Ereignisdauer: 51,6 min · laut Bericht: “fallas”
    Wörtliches Zitat anzeigen
    obteniendo un MTBF promedio de 378.36 minutos (Visualizar Fig. 7), un MTTR promedio de 51.55 minutos
  46. Anteil an der Verlustzeit: 27,0 % · laut Bericht: “technical machinery failures”
    Wörtliches Zitat anzeigen
    technical machinery failures, which accounted for 27.01% and could be mitigated through autonomous maintenance based on 5S principles within a TPM framework.
  47. Anteil an der Verlustzeit: 50,0 % · laut Bericht: “Equipment Failure Losses”
    Wörtliches Zitat anzeigen
    Equipment Failure Losses 20.205 20.205 50% 50%
  48. Verlustzeit: 20.205 Minutes · laut Bericht: “Equipment Failure Losses”
    Wörtliches Zitat anzeigen
    Equipment Failure Losses 20.205 20.205 50% 50%
  49. Zeit zwischen Ereignissen: 22,6 h · laut Bericht: “mechanical failure (corrective intervention)”
    Wörtliches Zitat anzeigen
    The baseline Mean Time Between Failures (MTBF) was 22.61 hours with a standard deviation of 10.91 hours; average corrective intervention time was 11.69 hours (see Table 4).
  50. Mittlere Ereignisdauer: 11,7 h · laut Bericht: “mechanical failure (corrective intervention)”
    Wörtliches Zitat anzeigen
    The baseline Mean Time Between Failures (MTBF) was 22.61 hours with a standard deviation of 10.91 hours; average corrective intervention time was 11.69 hours (see Table 4).
  51. Zeit zwischen Ereignissen: 32,0 h · laut Bericht: “mechanical failure”
    Wörtliches Zitat anzeigen
    on the 3rd of that month, 32 hours of operation were recorded until intervention, while on the 29th of the same month, only 6.25 hours were reached before maintenance was required.
  52. Zeit zwischen Ereignissen: 6,25 h · laut Bericht: “mechanical failure”
    Wörtliches Zitat anzeigen
    on the 3rd of that month, 32 hours of operation were recorded until intervention, while on the 29th of the same month, only 6.25 hours were reached before maintenance was required.
  53. Verlustzeit: 83,0 Jam · laut Bericht: “Breakdown Losses”
    Wörtliches Zitat anzeigen
    Kegagalan karena Breakdown Losses 83,03 31,45 Sangat Tinggi
  54. Anteil an der Verlustzeit: 31,5 % · laut Bericht: “Breakdown Losses”
    Wörtliches Zitat anzeigen
    diketahui bahwa faktor kegagalan berasal dari Breakdown Losses sebesar 31,45%, Reduced Speed Losses sebesar 24,73%, dan Idling and Minor Stoppages sebesar 18,64%.
  55. Zeit zwischen Ereignissen: 117 h · laut Bericht: “mechanical failure”
    Wörtliches Zitat anzeigen
    Furthermore, the mechanical MTBF increased from 98.74 h to 117.25 h, while the electrical MTBF increased from 144.31 h to 170.55 h.
  56. Mittlere Ereignisdauer: 7,50 h · laut Bericht: “mechanical failure”
    Wörtliches Zitat anzeigen
    the mechanical MTTR decreased from 9.73 h to 7.50 h
  57. Zeit zwischen Ereignissen: 98,7 h · laut Bericht: “mechanical failure”
    Wörtliches Zitat anzeigen
    Furthermore, the mechanical MTBF increased from 98.74 h to 117.25 h, while the electrical MTBF increased from 144.31 h to 170.55 h.
  58. Mittlere Ereignisdauer: 9,73 h · laut Bericht: “mechanical failure”
    Wörtliches Zitat anzeigen
    the mechanical MTTR decreased from 9.73 h to 7.50 h
  59. Anteil an der Verlustzeit: 25,0 % · laut Bericht: “Breakdown loss”
    Wörtliches Zitat anzeigen
    Breakdown loss 25