foratvise
Get Started
Process defects (scrap and rework)

Missing or defective cap/seal on container

Process defects (scrap and rework)QualityCapping and seaming

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 47 % of the line's lost time. Reported by 1 of the 82 studies that could observe it (sparse evidence).

What happens

During capping or seaming, a container may pass through the station without a cap being applied, with a cap that is not fully seated, or with a seam that is not properly formed, often due to cap feeding faults, worn chucks or sealing heads, or misaligned containers. The resulting units fail the capping/sealing specification at first pass and are rejected as nonconforming.

What is done about it

Perform preventive inspection and replacement of chucks, sealing heads and cap-feed components according to wear, and verify cap feeder orientation and timing settings. Install or tune downstream vision or torque/seal integrity checks to detect and segregate defective units immediately, and feed defect data back to adjust capping head pressure and alignment.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.7% [0.1–1.9%]
Expected share of lost time
0.3% [0.1–0.9%]
Share of lost time when present
47% [35–59%]
Studies / units
82 / 109
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.1% [0.1–3.9%]11 studies
  • Soft drinks, bottled water and juices
    0.6% [0.1–2.2%]26 studies
  • Brewing, wine and spirits
    0.7% [0.1–2.7%]11 studies
  • Bakery and pasta
    0.8% [0.1–3.2%]0 studies
  • Meat, poultry and seafood
    0.8% [0.1–2.8%]7 studies
  • Fruit and vegetable processing
    0.8% [0.1–3.0%]4 studies
  • Grain and oilseed milling
    0.8% [0.1–3.1%]3 studies
  • Sugar and confectionery
    0.8% [0.1–2.8%]3 studies
  • Snacks, coffee, tea and other foods
    0.8% [0.1–2.9%]4 studies
  • Animal feed and pet food
    0.8% [0.1–2.8%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.7% [0.1–2.8%]9 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During capping or seaming, a container may pass through the station without a cap being applied, with a cap that is not fully seated, or with a seam that is not properly formed, often due to cap feeding faults, worn chucks or sealing heads, or misaligned containers. The resulting units fail the capping/sealing specification at first pass and are rejected as nonconforming.

How it looks in SCADA data

Engineering guidance

MES/SCADA shows rejects counted at the capper/seamer discharge or at a downstream vision/seal inspection station, often linked to a specific cap-feeder or sealing-head fault code, with reject rate rising in bursts rather than continuously. Associated minor-stop or alarm counters on the cap feeder or chuck may correlate with the defect spikes.

Countermeasure

Engineering guidance

Perform preventive inspection and replacement of chucks, sealing heads and cap-feed components according to wear, and verify cap feeder orientation and timing settings. Install or tune downstream vision or torque/seal integrity checks to detect and segregate defective units immediately, and feed defect data back to adjust capping head pressure and alignment.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 9.90 Ton · as reported: “Producto s/Tapa”
    Show verbatim quote
    se redujeron las fallas por producto sin tapa de 10.8 a 9.9 toneladas un beneficio del 15.2% durante el periodo.
  2. Lost time: 10.8 Ton · as reported: “Producto s/Tapa”
    Show verbatim quote
    se redujeron las fallas por producto sin tapa de 10.8 a 9.9 toneladas un beneficio del 15.2% durante el periodo.
  3. Defect rate: 7.56 % · as reported: “productos no conformes (PNC) de la máquina cerradora”
    Show verbatim quote
    para la identificación de la máquina que realiza mayor cantidad de PNC es la máquina cerradora equivalente al 7.56% estando encima del margen establecido por la empresa de un 3%
  4. Defect rate: 1.00 % · as reported: “Kondisi Cap”
    Show verbatim quote
    Kondisi Cap 3808 1% 89%
  5. Defect rate: 4.00 % · as reported: “Tanpa Cap”
    Show verbatim quote
    Tanpa Cap 15018 4% 100%
  6. Number of events: 3,808 units · as reported: “Kondisi Cap”
    Show verbatim quote
    Kondisi Cap | 3808 | 1% | 89%
  7. Share of loss events: 1.00 % · as reported: “Kondisi Cap”
    Show verbatim quote
    Kondisi Cap | 3808 | 1% | 89%
  8. Number of events: 15,018 units · as reported: “Tanpa Cap”
    Show verbatim quote
    Tanpa Cap | 15018 | 4% | 100%
  9. Share of loss events: 4.00 % · as reported: “Tanpa Cap”
    Show verbatim quote
    Tanpa Cap | 15018 | 4% | 100%