Capping/sealing equipment failure
In short
It appears in about 1 of every 100 lines studied.
When it appears, it takes on average about 60 % of the line's lost time. Reported by 4 of the 82 studies that could observe it (limited evidence).
What happens
A component of the capping or seaming station degrades or malfunctions, such as a temperature sensor (thermocouple) that drifts, opens circuit or stops giving a reliable reading, or a mechanical capping head fault, so the station can no longer apply or verify caps or seals correctly and must be stopped for diagnosis and repair.
What is done about it
Apply preventive maintenance and periodic calibration or replacement of temperature sensors and capping head wear parts, use redundant or self-diagnosing sensors where feasible, and keep rapid-swap spare components on hand to minimize repair time when a fault occurs.
Practical guidance written from engineering knowledge; it is not a statistical estimate.
1Probability and evidence
- Probability of presence
- 1.1% [0.3–3.0%]
- Expected share of lost time
- 0.7% [0.2–1.8%]
- Share of lost time when present
- 60% [50–70%]
- Studies / units
- 82 / 109
- Evidence grade
- C
Grade C: 2 to 4 studies, or an interval wider than 0.35.
2Probability by segment
- Dairy products1.2% [0.2–4.2%]11 studies
- Soft drinks, bottled water and juices2.4% [0.5–6.2%]26 studies
- Brewing, wine and spirits1.2% [0.2–4.2%]11 studies
- Bakery and pasta1.4% [0.2–5.0%]0 studies
- Meat, poultry and seafood1.3% [0.2–4.4%]7 studies
- Fruit and vegetable processing1.3% [0.2–4.6%]4 studies
- Grain and oilseed milling1.4% [0.2–4.7%]3 studies
- Sugar and confectionery1.3% [0.2–5.0%]3 studies
- Snacks, coffee, tea and other foods1.3% [0.2–4.3%]4 studies
- Animal feed and pet food1.3% [0.2–4.7%]4 studies
- Food manufacturing (unspecified or mixed)1.3% [0.2–4.3%]9 studies
3Mechanism, SCADA signature and countermeasure
Mechanism
Engineering guidanceA component of the capping or seaming station degrades or malfunctions, such as a temperature sensor (thermocouple) that drifts, opens circuit or stops giving a reliable reading, or a mechanical capping head fault, so the station can no longer apply or verify caps or seals correctly and must be stopped for diagnosis and repair.
How it looks in SCADA data
Engineering guidanceSCADA/MES logs show a fault or alarm code on the capping/seaming station, often a sensor out-of-range or open-circuit alarm for temperature inputs, the machine state transitioning to fault/down with no cycle completion signal, and downstream equipment entering starvation while upstream units accumulate or are blocked.
Countermeasure
Engineering guidanceApply preventive maintenance and periodic calibration or replacement of temperature sensors and capping head wear parts, use redundant or self-diagnosing sensors where feasible, and keep rapid-swap spare components on hand to minimize repair time when a fault occurs.
4Sources
- Share of loss events: 38.0 % · as reported: “Falha no termopar”
Show verbatim quote
Analisando o efeito desta barra de selagem nas paradas ou ineficiência da enchedora Klockner, verificou-se que ele representava 38% das falhas, logo esta causa não foi validada como causa-raiz;
- Number of events: 249 events · as reported: “Kapaklama”
Show verbatim quote
KAPAKLAMA | Kapaklama | 249
- Number of events: 119 events · as reported: “Kapaklama”
Show verbatim quote
KAPAKLAMA | Kapaklama | 119
- COMPARATIVE ANALYSIS OF PRODUCTION LINE EFFICIENCY UNDER VARYING DEMAND SCENARIOS USING MULTILAYER PERCEPTRON (2026)Open sourceLost time: 4.70 hrs · as reported: “Capper Inconsistency”
Show verbatim quote
2 Fanta Orange 35cl 24 17,000 14,980 4.7 Capper Inconsistency 78.7 Operator shortage

