foratvise
Get Started
Process defects (scrap and rework)

Defective containers and closures (warped bottles, cap defects)

Process defects (scrap and rework)QualityWhole line or unspecified equipment

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 2 of the 127 studies that could observe it (limited evidence).

What happens

Nonconforming bottles and caps enter the line due to upstream moulding or blowing defects such as uneven wall thickness, incomplete cooling, flash or dimensional deviation, producing warped, cracked or out-of-tolerance containers and closures. These nonconformities are not corrected by the filling or capping process and result in finished units that fail quality checks for shape, seal integrity or closure fit.

What is done about it

Strengthen incoming inspection and acceptance criteria for containers and closures, and work with the moulding or blowing supplier to tighten dimensional and cooling process controls. Add or recalibrate inline vision or gauge inspection upstream of filling to detect and divert defective containers before they reach capping and packaging.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.7% [0.2–1.8%]
Expected share of lost time
0.3% [0.1–0.9%]
Share of lost time when present
48% [36–59%]
Studies / units
127 / 161
Evidence grade
C

Grade C: 2 to 4 studies, or an interval wider than 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.8% [0.1–2.9%]13 studies
  • Soft drinks, bottled water and juices
    1.3% [0.2–3.9%]26 studies
  • Brewing, wine and spirits
    0.8% [0.1–2.7%]11 studies
  • Bakery and pasta
    0.7% [0.1–2.4%]24 studies
  • Meat, poultry and seafood
    0.8% [0.1–2.9%]9 studies
  • Fruit and vegetable processing
    0.8% [0.1–2.8%]7 studies
  • Grain and oilseed milling
    0.8% [0.1–3.0%]6 studies
  • Sugar and confectionery
    0.8% [0.1–2.8%]9 studies
  • Snacks, coffee, tea and other foods
    0.8% [0.1–2.8%]5 studies
  • Animal feed and pet food
    0.8% [0.1–2.8%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.8% [0.1–3.0%]10 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Nonconforming bottles and caps enter the line due to upstream moulding or blowing defects such as uneven wall thickness, incomplete cooling, flash or dimensional deviation, producing warped, cracked or out-of-tolerance containers and closures. These nonconformities are not corrected by the filling or capping process and result in finished units that fail quality checks for shape, seal integrity or closure fit.

How it looks in SCADA data

Engineering guidance

Rejection counters at inspection, checkweighing or vision stations rise without any associated equipment fault or downtime alarm, and capper torque or seal-test readings show out-of-range values. Downgrade or scrap tallies increase while machine states remain in normal run, pointing to an incoming-material quality issue rather than a machine stop.

Countermeasure

Engineering guidance

Strengthen incoming inspection and acceptance criteria for containers and closures, and work with the moulding or blowing supplier to tighten dimensional and cooling process controls. Add or recalibrate inline vision or gauge inspection upstream of filling to detect and divert defective containers before they reach capping and packaging.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Number of events: 61.0 units · as reported: “Defective bottles”
    Show verbatim quote
    Defective bottles (unit) 172 61 -64.53%
  2. Number of events: 172 units · as reported: “Defective bottles”
    Show verbatim quote
    Defective bottles (unit) 172 61 -64.53%
  3. Defect rate: 2.00 % · as reported: “Cap defects, bottle warping”
    Show verbatim quote
    May 115,000 2,300 Cap defects, bottle warping 2.0 Supplier quality review