foratvise
Get Started

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 56 % of the line's lost time. Reported by 0 of the 112 studies that could observe it (sparse evidence).

What happens

The blade or knife used to cut film, trim product, or separate packs wears, chips, dulls or breaks due to fatigue, impact with foreign material, or accumulated cycle count, so it stops producing a clean cut and the machine must be stopped for the component to be replaced. This is a major component failure because restoring function requires a maintenance intervention rather than a simple operator clearance.

What is done about it

Implement a preventive replacement schedule for blades based on cycle count or wear inspection rather than run-to-failure, use wear-resistant or self-sharpening blade materials, and install metal detection or foreign-material screening upstream of the cutting station to reduce impact damage. Keep spare blades pre-sharpened and staged to shorten the change-out time when failure does occur.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.1%]
Expected share of lost time
0.2% [0.0–0.6%]
Share of lost time when present
56% [44–66%]
Studies / units
112 / 155
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.5% [0.0–1.7%]14 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.4%]33 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.7%]14 studies
  • Bakery and pasta
    0.5% [0.0–1.9%]6 studies
  • Meat, poultry and seafood
    0.5% [0.0–1.8%]6 studies
  • Fruit and vegetable processing
    0.5% [0.0–2.1%]4 studies
  • Grain and oilseed milling
    0.5% [0.0–1.9%]4 studies
  • Sugar and confectionery
    0.5% [0.0–1.9%]4 studies
  • Snacks, coffee, tea and other foods
    0.5% [0.0–1.8%]8 studies
  • Animal feed and pet food
    0.5% [0.0–1.9%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.5% [0.0–1.7%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The blade or knife used to cut film, trim product, or separate packs wears, chips, dulls or breaks due to fatigue, impact with foreign material, or accumulated cycle count, so it stops producing a clean cut and the machine must be stopped for the component to be replaced. This is a major component failure because restoring function requires a maintenance intervention rather than a simple operator clearance.

How it looks in SCADA data

Engineering guidance

SCADA/MES logs show an unplanned stop with a maintenance-type alarm or fault code related to the cutting station, often preceded by rising motor torque or current on the cutting drive, increasing cut-quality or tear rejects at the inspection station, and a downstream starvation pattern as upstream stations continue to run or buffer while the cut station is blocked for repair. The stop state duration is typically long enough to be logged as a maintenance event rather than a minor stop.

Countermeasure

Engineering guidance

Implement a preventive replacement schedule for blades based on cycle count or wear inspection rather than run-to-failure, use wear-resistant or self-sharpening blade materials, and install metal detection or foreign-material screening upstream of the cutting station to reduce impact damage. Keep spare blades pre-sharpened and staged to shorten the change-out time when failure does occur.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 0.790 % · as reported: “Major component failure/Cutting Blade Change”
    Show verbatim quote
    Major component failure/ Cutting Blade Change 0.79% 0.77% 0.71%
  2. Share of lost time: 0.710 % · as reported: “Major component failure/Cutting Blade Change”
    Show verbatim quote
    Major component failure/ Cutting Blade Change 0.79% 0.77% 0.71%
  3. Number of events: 131 occurrences · as reported: “worn knives due to prolonged use, such as broken, misaligned, or jammed knives”
    Show verbatim quote
    issues with worn knives due to prolonged use, such as broken, misaligned, or jammed knives, have caused downtime for the machines, contributing 1462 minutes of downtime and 131 occurrences.
  4. Lost time: 1,462 minutes · as reported: “worn knives due to prolonged use, such as broken, misaligned, or jammed knives”
    Show verbatim quote
    issues with worn knives due to prolonged use, such as broken, misaligned, or jammed knives, have caused downtime for the machines, contributing 1462 minutes of downtime and 131 occurrences.