Extruder changeover (die/recipe change and line clearing)
In short
It appears in about 2 of every 100 lines studied.
When it appears, it takes on average about 58 % of the line's lost time. Reported by 4 of the 59 studies that could observe it (limited evidence).
What happens
To switch product, recipe or pellet format the extruder must be stopped, the die and screw assembly changed or cleared of the previous mixture, and new process parameters (feed rate, moisture, temperature, screw speed) re-established before stable output resumes. Insufficient or inconsistent raw material feed during this transition forces reformatting of the mixture, extending the non-productive interval and often generating off-spec product.
What is done about it
Standardize die-change and recipe-change procedures with quick-release tooling, pre-staged dies and pre-weighed recipe batches to shorten the changeover window, applying SMED-type analysis to separate internal and external setup tasks. Verify raw material availability and consistency before initiating a recipe change to avoid mid-run reformatting, and define a short, monitored warm-up/purge sequence with clear acceptance criteria before releasing product to the line.
Practical guidance written from engineering knowledge; it is not a statistical estimate.
1Probability and evidence
- Probability of presence
- 1.6% [0.4–4.2%]
- Expected share of lost time
- 0.9% [0.2–2.5%]
- Share of lost time when present
- 58% [47–69%]
- Studies / units
- 59 / 72
- Evidence grade
- C
Grade C: 2 to 4 studies, or an interval wider than 0.35.
2Probability by segment
- Dairy products1.8% [0.2–6.6%]5 studies
- Soft drinks, bottled water and juices1.9% [0.2–7.0%]1 study
- Brewing, wine and spirits1.9% [0.2–7.3%]0 studies
- Bakery and pasta1.5% [0.2–4.8%]23 studies
- Meat, poultry and seafood1.9% [0.2–7.4%]2 studies
- Fruit and vegetable processing1.9% [0.2–6.6%]2 studies
- Grain and oilseed milling1.9% [0.2–7.3%]0 studies
- Sugar and confectionery1.7% [0.2–5.7%]8 studies
- Snacks, coffee, tea and other foods2.5% [0.3–8.0%]5 studies
- Animal feed and pet food3.8% [0.5–13.0%]6 studies
- Food manufacturing (unspecified or mixed)1.8% [0.2–6.3%]7 studies
3Mechanism, SCADA signature and countermeasure
Mechanism
Engineering guidanceTo switch product, recipe or pellet format the extruder must be stopped, the die and screw assembly changed or cleared of the previous mixture, and new process parameters (feed rate, moisture, temperature, screw speed) re-established before stable output resumes. Insufficient or inconsistent raw material feed during this transition forces reformatting of the mixture, extending the non-productive interval and often generating off-spec product.
How it looks in SCADA data
Engineering guidanceThe extruder state changes to setup/changeover or idle, feed and screw speed set-points drop to zero or to warm-up values, die and barrel temperatures ramp while torque and head pressure oscillate, and the good-unit counter stalls while a changeover or clear-line code is active in the event log. Repeated short stop-start cycles and quality-hold flags often follow immediately after the state returns to run, reflecting the stabilization period.
Countermeasure
Engineering guidanceStandardize die-change and recipe-change procedures with quick-release tooling, pre-staged dies and pre-weighed recipe batches to shorten the changeover window, applying SMED-type analysis to separate internal and external setup tasks. Verify raw material availability and consistency before initiating a recipe change to avoid mid-run reformatting, and define a short, monitored warm-up/purge sequence with clear acceptance criteria before releasing product to the line.
4Sources
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceLost time: 12.2 h · as reported: “Die Change (เปลี่ยน DIE)”
Show verbatim quote
เปลี่ยน DIE 12.17
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceLost time: 5.33 h · as reported: “Break Down (เสียรอซอม)”
Show verbatim quote
เสียรอซอม(Break Down) 5.33
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceLost time: 25.4 h · as reported: “Clear line / recipe change (Clear line เปลี่ยนสูตร)”
Show verbatim quote
Clear line เปลี่ยนสูตร 25.4
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceLost time: 8.00 h · as reported: “Production stop (หยุดผลิต)”
Show verbatim quote
หยุดผลิต 8
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceLost time: 0 h · as reported: “Cleaning (ทําความสะอาด)”
Show verbatim quote
ทําความสะอาด 0
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceDefect rate: 0.600 ตัน · as reported: “Short pellet size (ขนาดเม็ดสั้น)”
Show verbatim quote
ขนาดเม็ดสั้น 0.60
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceDefect rate: 1.20 ตัน · as reported: “Two colors (สองสี)”
Show verbatim quote
สองสี 1.20
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceDefect rate: 0 ตัน · as reported: “Wet lump (กอนเปยกปน)”
Show verbatim quote
กอนเปยกปน 0.00
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceDefect rate: 0 ตัน · as reported: “Excess dust (ฝุนเกินมาตรฐาน)”
Show verbatim quote
ฝุนเกินมาตรฐาน 0.00
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceDefect rate: 0.500 ตัน · as reported: “Burnt pellet (เม็ดไหม)”
Show verbatim quote
เม็ดไหม 0.50
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceDefect rate: 0 ตัน · as reported: “Durability test failure (คาความคงทนไมผาน)”
Show verbatim quote
คาความคงทนไมผาน 0.00
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceDefect rate: 59.4 ตัน · as reported: “Reprocess”
Show verbatim quote
Reprocess 59.37
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceLost time: 38.3 h · as reported: “Break Down”
Show verbatim quote
Bre ak D ow n Machine Adjus tme nt Die Ch an ge Waiting Time C lea rline 38.33 105.00 112.17 149.83 181.67 6.5 17.9 19.1 25.5 30.9 100.0 93.5 75.6 56.5 30.9
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceShare of lost time: 6.50 % · as reported: “Break Down”
Show verbatim quote
Bre ak D ow n Machine Adjus tme nt Die Ch an ge Waiting Time C lea rline 38.33 105.00 112.17 149.83 181.67 6.5 17.9 19.1 25.5 30.9 100.0 93.5 75.6 56.5 30.9
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceLost time: 112 h · as reported: “Die Change”
Show verbatim quote
Bre ak D ow n Machine Adjus tme nt Die Ch an ge Waiting Time C lea rline 38.33 105.00 112.17 149.83 181.67 6.5 17.9 19.1 25.5 30.9 100.0 93.5 75.6 56.5 30.9
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceShare of lost time: 19.1 % · as reported: “Die Change”
Show verbatim quote
Bre ak D ow n Machine Adjus tme nt Die Ch an ge Waiting Time C lea rline 38.33 105.00 112.17 149.83 181.67 6.5 17.9 19.1 25.5 30.9 100.0 93.5 75.6 56.5 30.9
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceLost time: 182 h · as reported: “Clearline”
Show verbatim quote
Bre ak D ow n Machine Adjus tme nt Die Ch an ge Waiting Time C lea rline 38.33 105.00 112.17 149.83 181.67 6.5 17.9 19.1 25.5 30.9 100.0 93.5 75.6 56.5 30.9
- การเพิ่มผลผลิตด้วยวิธีการปรับปรุงประสิทธิผลโดยรวมของเครื่องจักร : กรณีศึกษา โรงงานผลิตอาหารสัตว์ (2010)Open sourceShare of lost time: 30.9 % · as reported: “Clearline”
Show verbatim quote
Bre ak D ow n Machine Adjus tme nt Die Ch an ge Waiting Time C lea rline 38.33 105.00 112.17 149.83 181.67 6.5 17.9 19.1 25.5 30.9 100.0 93.5 75.6 56.5 30.9
- Propuesta de implementación de un sistema de aspiración basado en la metodología lean manufacturing en el proceso de extrusión, para incrementar la capacidad de producción en una empresa productora de alimento balanceado acuícola (2016)Open sourceLost time: 38.5 min · as reported: “reformatting (lack of mixture)”
Show verbatim quote
reduce time 210.44 reformatting minutes to 38.47 minutes
- Propuesta de implementación de un sistema de aspiración basado en la metodología lean manufacturing en el proceso de extrusión, para incrementar la capacidad de producción en una empresa productora de alimento balanceado acuícola (2016)Open sourceLost time: 210 min · as reported: “reformatting (lack of mixture)”
Show verbatim quote
reduce time 210.44 reformatting minutes to 38.47 minutes
- Robust DMAIC-Driven Optimization of Expansion Index in Cereal Extrusion Using DOE and SHAP-Based Factor Screening (2026)Open sourceLost time: 600 min/week · as reported: “unplanned downtime”
Show verbatim quote
unplanned downtime decreasing from 600 to 300 min/week
- Robust DMAIC-Driven Optimization of Expansion Index in Cereal Extrusion Using DOE and SHAP-Based Factor Screening (2026)Open sourceLost time: 300 min/week · as reported: “unplanned downtime”
Show verbatim quote
unplanned downtime decreasing from 600 to 300 min/week

