foratvise
Get Started
Process defects (scrap and rework)

Fill content or contamination defect

Process defects (scrap and rework)QualityFilling

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 2 of the 120 studies that could observe it (limited evidence).

What happens

Variability in the dosing or filling valve, flow meter drift, or changes in product viscosity and temperature cause the delivered volume or weight of product (for example oil content) to fall below specification. Separately, ingress of foreign matter, residual cleaning or sanitising agents, or microbial contamination during the filling step renders units unfit for use even when the fill level itself is correct.

What is done about it

Calibrate and periodically verify dosing valves, pumps and flow meters against reference standards, and compensate for product viscosity and temperature in the filling control logic. Reinforce cleaning and sanitation validation, use foreign-particle or seal-integrity detection where applicable, and route borderline units to checkweighing and quality inspection before release.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.7% [0.2–2.0%]
Expected share of lost time
0.4% [0.1–1.0%]
Share of lost time when present
48% [37–60%]
Studies / units
120 / 162
Evidence grade
C

Grade C: 2 to 4 studies, or an interval wider than 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.8% [0.1–2.8%]18 studies
  • Soft drinks, bottled water and juices
    0.9% [0.1–2.5%]44 studies
  • Brewing, wine and spirits
    0.8% [0.1–2.7%]16 studies
  • Bakery and pasta
    0.9% [0.1–3.5%]0 studies
  • Meat, poultry and seafood
    0.8% [0.1–2.9%]6 studies
  • Fruit and vegetable processing
    0.9% [0.1–3.2%]4 studies
  • Grain and oilseed milling
    1.3% [0.2–4.6%]6 studies
  • Sugar and confectionery
    0.9% [0.1–3.2%]3 studies
  • Snacks, coffee, tea and other foods
    0.9% [0.1–3.1%]6 studies
  • Animal feed and pet food
    0.9% [0.1–3.2%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.8% [0.1–2.8%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Variability in the dosing or filling valve, flow meter drift, or changes in product viscosity and temperature cause the delivered volume or weight of product (for example oil content) to fall below specification. Separately, ingress of foreign matter, residual cleaning or sanitising agents, or microbial contamination during the filling step renders units unfit for use even when the fill level itself is correct.

How it looks in SCADA data

Engineering guidance

In-line checkweigher or flow totaliser readings trend below the target setpoint with increasing reject counts at the filling station; dosing valve or pump actuator signals show drift or erratic cycles. Contamination events are less directly visible in SCADA but may correlate with CIP cycle timing, missed sanitation confirmations, or downstream quality-inspection reject spikes without any corresponding deviation in fill-level signals.

Countermeasure

Engineering guidance

Calibrate and periodically verify dosing valves, pumps and flow meters against reference standards, and compensate for product viscosity and temperature in the filling control logic. Reinforce cleaning and sanitation validation, use foreign-particle or seal-integrity detection where applicable, and route borderline units to checkweighing and quality inspection before release.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of loss events: 15.0 % · as reported: “Less Content Oil”
    Show verbatim quote
    Less Content Oil 676 15
  2. Number of events: 676 units · as reported: “Less Content Oil”
    Show verbatim quote
    Less Content Oil 676 15
  3. Number of events: 8,124 cases · as reported: “Contaminated”
    Show verbatim quote
    Among these, underfill defects were the most frequent, with a total of 20,598 cases, followed by uncrowned bottles with 14,508 cases, and contamination with 8,124 cases.