foratvise
Get Started
organizational external

Operator-related inefficiency

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 56 % of the line's lost time. Reported by 1 of the 127 studies that could observe it (sparse evidence).

What happens

Line performance is limited by the human factor rather than by equipment condition: insufficient staffing, operator absence, lack of training or slow manual task execution delays restarts and keeps the line running below its rated rate. The loss is attributed to labour organisation rather than to a mechanical, electrical or process cause.

What is done about it

Ensure adequate staffing levels and cross-training, standardise work instructions for manual tasks, and monitor operator-attributed stop and speed-loss time to identify and close skill or staffing gaps.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.5%]
Expected share of lost time
0.3% [0.1–0.8%]
Share of lost time when present
56% [45–66%]
Studies / units
127 / 161
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.4%]13 studies
  • Soft drinks, bottled water and juices
    0.5% [0.1–1.9%]26 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.2%]11 studies
  • Bakery and pasta
    0.8% [0.1–2.7%]24 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.2%]9 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.4%]7 studies
  • Grain and oilseed milling
    0.6% [0.1–2.3%]6 studies
  • Sugar and confectionery
    0.6% [0.1–2.5%]9 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.3%]5 studies
  • Animal feed and pet food
    0.6% [0.1–2.2%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.4%]10 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Line performance is limited by the human factor rather than by equipment condition: insufficient staffing, operator absence, lack of training or slow manual task execution delays restarts and keeps the line running below its rated rate. The loss is attributed to labour organisation rather than to a mechanical, electrical or process cause.

How it looks in SCADA data

Engineering guidance

Stop or downtime events are logged under a generic manual/operator reason code with no associated equipment fault or alarm, often with extended line-stopped duration while waiting for an operator action. Running periods show actual speed persistently below the target set point without any corresponding equipment degradation signal.

Countermeasure

Engineering guidance

Ensure adequate staffing levels and cross-training, standardise work instructions for manual tasks, and monitor operator-attributed stop and speed-loss time to identify and close skill or staffing gaps.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 4.00 min · as reported: “Operational (man)”
    Show verbatim quote
    Operational (man) 10 0 0 5 13 0 0 4 0 0 0 27
  2. Lost time: 5.00 min · as reported: “Operational (man)”
    Show verbatim quote
    Operational (man) 10 0 0 5 13 0 0 4 0 0 0 27
  3. Lost time: 13.0 min · as reported: “Operational (man)”
    Show verbatim quote
    Operational (man) 10 0 0 5 13 0 0 4 0 0 0 27
  4. Lost time: 10.0 min · as reported: “Operational (man)”
    Show verbatim quote
    Operational (man) 10 0 0 5 13 0 0 4 0 0 0 27
  5. Lost time: 27.0 min · as reported: “Operational (man)”
    Show verbatim quote
    Operational (man) 10 0 0 5 13 0 0 4 0 0 0 27
  6. Share of lost time: 46.5 % · as reported: “low operational performance”
    Show verbatim quote
    The analysis revealed three main reasons contributing to this issue: production line stoppages accounted for 49.2% of the problem, followed by low operational performance with a contribution of 46.5%, and a smaller share of 4.3% attributed to defective products.