foratvise
Get Started
Process defects (scrap and rework)

Rice polishing process defect (grain breakage/over-polishing)

Process defects (scrap and rework)QualityMilling and grinding

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 1 of the 43 studies that could observe it (sparse evidence).

What happens

During rice polishing, excessive friction between the grain and the abrasive rollers, incorrect roller clearance or pressure, or unsuitable grain moisture content causes grains to crack, break or lose excessive bran layer. This yields product that fails whiteness, breakage-rate or appearance specifications during stable production, so the output is rejected or downgraded rather than being an unplanned stop.

What is done about it

Calibrate and periodically adjust roller clearance and polishing pressure to the grain variety, verify incoming grain moisture before polishing, and replace worn abrasive rollers or screens on a preventive schedule. In-process sampling of whiteness and breakage rate allows closed-loop adjustment of polishing intensity before defect levels rise.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.9% [0.2–2.7%]
Expected share of lost time
0.4% [0.1–1.3%]
Share of lost time when present
48% [36–59%]
Studies / units
43 / 48
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.1% [0.1–4.2%]5 studies
  • Soft drinks, bottled water and juices
    1.1% [0.1–4.8%]1 study
  • Brewing, wine and spirits
    1.1% [0.1–4.6%]0 studies
  • Bakery and pasta
    1.1% [0.1–4.3%]0 studies
  • Meat, poultry and seafood
    1.1% [0.1–4.3%]0 studies
  • Fruit and vegetable processing
    1.1% [0.1–4.5%]2 studies
  • Grain and oilseed milling
    1.6% [0.1–6.1%]7 studies
  • Sugar and confectionery
    1.0% [0.1–3.7%]10 studies
  • Snacks, coffee, tea and other foods
    1.0% [0.1–3.7%]5 studies
  • Animal feed and pet food
    1.0% [0.1–4.0%]6 studies
  • Food manufacturing (unspecified or mixed)
    1.0% [0.1–3.9%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During rice polishing, excessive friction between the grain and the abrasive rollers, incorrect roller clearance or pressure, or unsuitable grain moisture content causes grains to crack, break or lose excessive bran layer. This yields product that fails whiteness, breakage-rate or appearance specifications during stable production, so the output is rejected or downgraded rather than being an unplanned stop.

How it looks in SCADA data

Engineering guidance

MES/quality data show elevated scrap, rework or downgrade counts attributed to the polishing station while the machine state log remains in normal run mode without fault alarms. Correlation can often be seen between polisher motor load, roller speed or pressure setpoints and spikes in rejected batches, without corresponding stop or fault events.

Countermeasure

Engineering guidance

Calibrate and periodically adjust roller clearance and polishing pressure to the grain variety, verify incoming grain moisture before polishing, and replace worn abrasive rollers or screens on a preventive schedule. In-process sampling of whiteness and breakage rate allows closed-loop adjustment of polishing intensity before defect levels rise.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 21.8 tons/year · as reported: “grain breakage during polishing”
    Show verbatim quote
    21.8 tons of grain breakage occur during the polishing stage
  2. Share of planned time: 15.0 % · as reported: “system loss (composition unspecified)”
    Show verbatim quote
    the system exhibited a mean loss rate of 15% with a wide interval of (10%; 20%)
  3. Share of lost time: 2.50 % · as reported: “process defect losses”
    Show verbatim quote
    Sementara itu, breakdown losses sebesar 3,33%, setup & adjustment losses sebesar 0,73%, dan process defect losses sebesar 2,5% tergolong rendah, sehingga tidak menjadi faktor dominan dalam penurunan kinerja mesin.
  4. Defect rate: 22.0 % · as reported: “head rice loss rate (อัตราการสูญเสียข้าว)”
    Show verbatim quote
    ในขั้นตอนการขัดขาวรอบที่ 1 มีอัตราการสูญเสียข้าวเป็นปริมาณมากถึง 22.00 % ทั้งนี้เนื่องมาจากการตั้งค่าความเร็วรอบสูงถึง 430 RPM
  5. Defect rate: 13.3 % · as reported: “head rice loss rate (อัตราการสูญเสียข้าว)”
    Show verbatim quote
    เมื่อปรับลดความเร็วรอบลงแล้วเก็บข้อมูลการขัดข้าวพบว่า มีอัตราการสูญเสียของข้าวลดลงเหลือเพียง 13.30 %