foratvise
Get Started
Setup and adjustments

Die or tooling retrieval delay during changeover

Setup and adjustmentsAvailabilityFilling

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 55 % of the line's lost time. Reported by 1 of the 120 studies that could observe it (sparse evidence).

What happens

During a format changeover the correct die or format-specific tooling for the filler is not available at the point of use, so operators must leave the line to locate it in storage or request it from another area. This searching time extends the external setup time because the die is needed before the machine can resume production, even though it could in principle be prepared in advance.

What is done about it

Apply SMED principles by converting this internal, line-stopping search into external preparation: stage and label all dies and format parts for the upcoming changeover at the point of use before the line stops, using shadow boards, kitting carts or a dedicated tooling storage system with clear location coding. Maintain a changeover parts checklist and assign retrieval tasks to a support operator in parallel with other preparation activities.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.5% [0.1–1.4%]
Expected share of lost time
0.3% [0.1–0.8%]
Share of lost time when present
55% [41–65%]
Studies / units
120 / 162
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.5% [0.1–1.9%]18 studies
  • Soft drinks, bottled water and juices
    0.5% [0.1–1.5%]44 studies
  • Brewing, wine and spirits
    0.8% [0.1–2.9%]16 studies
  • Bakery and pasta
    0.6% [0.1–2.5%]0 studies
  • Meat, poultry and seafood
    0.6% [0.1–2.2%]6 studies
  • Fruit and vegetable processing
    0.6% [0.1–2.3%]4 studies
  • Grain and oilseed milling
    0.6% [0.1–2.3%]6 studies
  • Sugar and confectionery
    0.6% [0.1–2.3%]3 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.1%]6 studies
  • Animal feed and pet food
    0.6% [0.1–2.3%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.1%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During a format changeover the correct die or format-specific tooling for the filler is not available at the point of use, so operators must leave the line to locate it in storage or request it from another area. This searching time extends the external setup time because the die is needed before the machine can resume production, even though it could in principle be prepared in advance.

How it looks in SCADA data

Engineering guidance

The line or filler remains in a changeover or setup state for an unusually long period with no fault alarms active, and no material or cycle counts are recorded. Operator or MES event logs may show a changeover step held open or a manual pause without any corresponding mechanical adjustment activity, and downstream stations show starvation during this interval.

Countermeasure

Engineering guidance

Apply SMED principles by converting this internal, line-stopping search into external preparation: stage and label all dies and format parts for the upcoming changeover at the point of use before the line stops, using shadow boards, kitting carts or a dedicated tooling storage system with clear location coding. Maintain a changeover parts checklist and assign retrieval tasks to a support operator in parallel with other preparation activities.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 13.0 min · as reported: “Procurar ferramenta”
    Show verbatim quote
    18 Procurar ferramenta 13 0
  2. Lost time: 0 min · as reported: “Procurar ferramenta”
    Show verbatim quote
    18 Procurar ferramenta 13 0
  3. Lost time: 2.00 min · as reported: “Search for new die”
    Show verbatim quote
    Search for new die 2 min 2 min External
  4. Lost time: 2.00 min · as reported: “Search for new die”
    Show verbatim quote
    Search for new die | 2 min | 2 min | External