foratvise
Get Started
not classifiable

Unspecified hammer mill stoppage

not classifiableMilling and grinding

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 2 of the 43 studies that could observe it (limited evidence).

What happens

The hammer mill accumulates stop time that the primary study reports only under broad generic buckets such as adjustment, breakdown, or idling, without identifying the specific mechanical, electrical, or operational root cause behind each event. Underlying physical triggers may include hammer or screen wear, feed jams, bearing degradation, or operator-paced restarts, but the available reporting does not distinguish among them.

What is done about it

Deploy structured downtime coding at the mill station so operators and maintenance staff tag each stop with a specific failure mode, enabling separation of breakdowns, adjustments, and minor stoppages for targeted root-cause analysis. Reviewing historical patterns once finer categorization is available supports prioritizing preventive maintenance and operator training on the dominant specific causes.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.4% [0.3–4.1%]
Expected share of lost time
0.8% [0.2–2.3%]
Share of lost time when present
57% [47–68%]
Studies / units
43 / 48
Evidence grade
C

Grade C: 2 to 4 studies, or an interval wider than 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.6% [0.2–6.0%]5 studies
  • Soft drinks, bottled water and juices
    1.6% [0.2–6.2%]1 study
  • Brewing, wine and spirits
    1.7% [0.2–6.4%]0 studies
  • Bakery and pasta
    1.7% [0.2–6.4%]0 studies
  • Meat, poultry and seafood
    1.7% [0.2–7.0%]0 studies
  • Fruit and vegetable processing
    1.6% [0.2–6.4%]2 studies
  • Grain and oilseed milling
    1.6% [0.2–5.5%]7 studies
  • Sugar and confectionery
    1.4% [0.2–5.0%]10 studies
  • Snacks, coffee, tea and other foods
    2.1% [0.2–7.5%]5 studies
  • Animal feed and pet food
    2.2% [0.3–7.9%]6 studies
  • Food manufacturing (unspecified or mixed)
    1.6% [0.2–6.0%]7 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The hammer mill accumulates stop time that the primary study reports only under broad generic buckets such as adjustment, breakdown, or idling, without identifying the specific mechanical, electrical, or operational root cause behind each event. Underlying physical triggers may include hammer or screen wear, feed jams, bearing degradation, or operator-paced restarts, but the available reporting does not distinguish among them.

How it looks in SCADA data

Engineering guidance

Machine-state logs show the mill cycling between run and stop states tagged with generic stop-reason codes mapped only to coarse categories, lacking fault-specific identifiers or correlated sensor data. Duration distributions mix brief idling clearances with longer maintenance interventions and setup-type adjustments under the same undifferentiated counters.

Countermeasure

Engineering guidance

Deploy structured downtime coding at the mill station so operators and maintenance staff tag each stop with a specific failure mode, enabling separation of breakdowns, adjustments, and minor stoppages for targeted root-cause analysis. Reviewing historical patterns once finer categorization is available supports prioritizing preventive maintenance and operator training on the dominant specific causes.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of planned time: 2.73 % · as reported: “Breakdown losses”
    Show verbatim quote
    Rata rata tahunan 2,73% 0,147% 15,214% 2,871% 1,565% 4,192%
  2. Share of planned time: 0.147 % · as reported: “Adjustment losses”
    Show verbatim quote
    Rata rata tahunan 2,73% 0,147% 15,214% 2,871% 1,565% 4,192%
  3. Share of planned time: 15.2 % · as reported: “Idling and stop losses”
    Show verbatim quote
    Rata rata tahunan 2,73% 0,147% 15,214% 2,871% 1,565% 4,192%
  4. Share of lost time: 75.0 % · as reported: “high unproductive times”
    Show verbatim quote
    At Level 1 of the analysis, the primary causes were identified as high unproductive times (75%) and frequent operator failures (25%).