foratvise
Get Started
Equipment failure (breakdowns)

V-belt breakage or slippage

Equipment failure (breakdowns)AvailabilityWhole line or unspecified equipment

In short

It appears in fewer than 1 of every 100 lines studied.

When it appears, it takes on average about 58 % of the line's lost time. Reported by 0 of the 127 studies that could observe it (sparse evidence).

What happens

The V-belt that transmits motion between motor and driven shaft wears, loses tension, becomes misaligned or ages until it cracks, stretches excessively or snaps, so the mechanical power transmission to the driven component (mill rotor, separator drive, etc.) is interrupted or degraded.

What is done about it

Implement periodic inspection and replacement of belts based on wear and tension condition, ensure correct pulley alignment and tensioning during installation, and consider belt tension or vibration monitoring to anticipate failure before it causes an unplanned stop.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.4% [0.1–1.1%]
Expected share of lost time
0.2% [0.0–0.6%]
Share of lost time when present
58% [47–68%]
Studies / units
127 / 161
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.4% [0.0–1.7%]13 studies
  • Soft drinks, bottled water and juices
    0.4% [0.0–1.5%]26 studies
  • Brewing, wine and spirits
    0.4% [0.0–1.6%]11 studies
  • Bakery and pasta
    0.4% [0.0–1.5%]24 studies
  • Meat, poultry and seafood
    0.4% [0.0–1.6%]9 studies
  • Fruit and vegetable processing
    0.4% [0.0–1.7%]7 studies
  • Grain and oilseed milling
    0.4% [0.0–1.7%]6 studies
  • Sugar and confectionery
    0.4% [0.0–1.7%]9 studies
  • Snacks, coffee, tea and other foods
    0.4% [0.0–1.7%]5 studies
  • Animal feed and pet food
    0.4% [0.0–1.7%]7 studies
  • Food manufacturing (unspecified or mixed)
    0.4% [0.0–1.7%]10 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The V-belt that transmits motion between motor and driven shaft wears, loses tension, becomes misaligned or ages until it cracks, stretches excessively or snaps, so the mechanical power transmission to the driven component (mill rotor, separator drive, etc.) is interrupted or degraded.

How it looks in SCADA data

Engineering guidance

Motor keeps running at normal or reduced current while driven shaft speed, torque or output flow drops toward zero; drive fault or underload alarm appears, and the machine state log shows an unplanned stop with downstream starvation on the affected unit.

Countermeasure

Engineering guidance

Implement periodic inspection and replacement of belts based on wear and tension condition, ensure correct pulley alignment and tensioning during installation, and consider belt tension or vibration monitoring to anticipate failure before it causes an unplanned stop.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Time between events: 6.00 Months · as reported: “V-Belt”
    Show verbatim quote
    V-Belt Break 6 Months
  2. Mean event duration: 4.00 jam · as reported: “v-belt mesin putus/kendor”
    Show verbatim quote
    Berdasarkan informasi dari pemilik perusahaan permasalahan yang terjadi pada mesin pengiling beras (Rice Milling Unit) yakni v-belt putus atau kendor sehingga mengakibatkan mesin berhenti dan tidak beroperasi + selama 4 jam.