Filler changeover and adjustment
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 4 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 56 % der Verlustzeit der Linie. Berichtet von 13 der 120 Studien, die sie beobachten konnten (starke Evidenz).
Was passiert
Time is lost between the last good unit of one filling run and the first good unit of the next because the filler must be stopped to change product-contact parts (nozzles, dosing elements, format guides), reset dosing or sealing parameters, and fine-tune the equipment until output stabilizes. This includes mechanical part exchange, parameter entry, and trial adjustments before the process reaches target fill accuracy and sealing quality.
Was man dagegen tut
Apply structured quick-changeover methods (SMED) to separate internal and external setup activities, pre-stage tooling and recipes, and use standardized work instructions with predefined parameter sets to reduce trial-and-error adjustment. Automating parameter recall and using tool-less quick-change fittings further shortens the non-productive interval.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 3,6 % [1,5–7,1 %]
- Erwarteter Anteil an der Verlustzeit
- 2,0 % [0,8–4,0 %]
- Anteil an der Verlustzeit bei Auftreten
- 56 % [45–65 %]
- Studien / Einheiten
- 120 / 162
- Evidenzgrad
- A
Grad A: 10 oder mehr Studien und 10 oder mehr verschiedene Linien, mit einem 95-%-Glaubwürdigkeitsintervall schmaler als 0,20.
2Wahrscheinlichkeit nach Segment
- Milchprodukte5,4 % [1,3–13,3 %]18 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte3,1 % [1,0–6,6 %]44 Studien
- Bier, Wein und Spirituosen5,1 % [1,3–12,1 %]16 Studien
- Backwaren und Teigwaren4,4 % [0,7–13,4 %]0 Studien
- Fleisch, Geflügel und Fisch4,8 % [1,0–13,2 %]6 Studien
- Obst- und Gemüseverarbeitung3,9 % [0,7–10,9 %]4 Studien
- Getreide- und Ölsaatenmüllerei3,7 % [0,7–10,7 %]6 Studien
- Zucker und Süßwaren4,0 % [0,7–11,6 %]3 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel6,6 % [1,5–18,0 %]6 Studien
- Futtermittel und Heimtiernahrung3,9 % [0,7–11,2 %]4 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)6,1 % [1,5–15,6 %]13 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseTime is lost between the last good unit of one filling run and the first good unit of the next because the filler must be stopped to change product-contact parts (nozzles, dosing elements, format guides), reset dosing or sealing parameters, and fine-tune the equipment until output stabilizes. This includes mechanical part exchange, parameter entry, and trial adjustments before the process reaches target fill accuracy and sealing quality.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseSCADA/MES shows an extended machine-state duration logged as changeover or setup, with the filler in a non-running state while upstream and downstream equipment may be starved or blocked; counters for good units remain flat during this interval. Repeated short cycles of state toggling between setup and run can appear as operators perform iterative fine adjustments before stable production is confirmed.
Gegenmaßnahme
Ingenieurpraktische HinweiseApply structured quick-changeover methods (SMED) to separate internal and external setup activities, pre-stage tooling and recipes, and use standardized work instructions with predefined parameter sets to reduce trial-and-error adjustment. Automating parameter recall and using tool-less quick-change fittings further shortens the non-productive interval.
4Quellen
- Verlustzeit: 38,0 min · laut Bericht: “Mudar e transportar peças de formato”
Wörtliches Zitat anzeigen
7, 8, 11, 12 Mudar e transportar peças de formato 38 20
- Verlustzeit: 14,0 min · laut Bericht: “Ajustes”
Wörtliches Zitat anzeigen
16 Ajustes 14 4
- Verlustzeit: 5,00 min · laut Bericht: “Testar enchimento”
Wörtliches Zitat anzeigen
21 Testar enchimento 5 0
- Verlustzeit: 1,00 min · laut Bericht: “Trazer a mangueira para junto da enchedora”
Wörtliches Zitat anzeigen
10 Trazer a mangueira para junto da enchedora 1 0
- Mittlere Ereignisdauer: 103 min · laut Bericht: “Mudança de tara”
Wörtliches Zitat anzeigen
Mudança de tara 102,5 min 42 min 60,5 min 1,07%
- Mittlere Ereignisdauer: 118 min · laut Bericht: “Mudança de cápsula”
Wörtliches Zitat anzeigen
Mudança de cápsula 118,4 min 55 min 63,4 min
- Mittlere Ereignisdauer: 152 min · laut Bericht: “Mudança de tara e cápsula”
Wörtliches Zitat anzeigen
Mudança de tara e cápsula 151,8 min 84 min 67,8 min
- Mittlere Ereignisdauer: 115 min · laut Bericht: “Mudança de tara (trabalho interno)”
Wörtliches Zitat anzeigen
A média da duração de trabalho interno das mudanças de tara observadas é de 115 minutos.
- Mittlere Ereignisdauer: 100 min · laut Bericht: “Mudança de cápsula (trabalho interno)”
Wörtliches Zitat anzeigen
A média da duração de trabalho interno das mudanças de cápsula observadas é de 100 minutos.
- Verlustzeit: 20,0 min · laut Bericht: “Mudar e transportar peças de formato”
Wörtliches Zitat anzeigen
7, 8, 11, 12 Mudar e transportar peças de formato 38 20
- Verlustzeit: 4,00 min · laut Bericht: “Ajustes”
Wörtliches Zitat anzeigen
16 Ajustes 14 4
- Verlustzeit: 0 min · laut Bericht: “Testar enchimento”
Wörtliches Zitat anzeigen
21 Testar enchimento 5 0
- Verlustzeit: 0 min · laut Bericht: “Trazer a mangueira para junto da enchedora”
Wörtliches Zitat anzeigen
10 Trazer a mangueira para junto da enchedora 1 0
- Mittlere Ereignisdauer: 42,0 min · laut Bericht: “Mudança de tara”
Wörtliches Zitat anzeigen
Mudança de tara 102,5 min 42 min 60,5 min 1,07%
- Mittlere Ereignisdauer: 55,0 min · laut Bericht: “Mudança de cápsula”
Wörtliches Zitat anzeigen
Mudança de cápsula 118,4 min 55 min 63,4 min
- Mittlere Ereignisdauer: 84,0 min · laut Bericht: “Mudança de tara e cápsula”
Wörtliches Zitat anzeigen
Mudança de tara e cápsula 151,8 min 84 min 67,8 min
- Mittlere Ereignisdauer: 30,0 min · laut Bericht: “Mudança de tara (trabalho interno)”
Wörtliches Zitat anzeigen
O diagrama de Gantt (Anexo E) indica que o trabalho interno de uma mudança de tara pode ser executado em 30 minutos e que, no total, o tempo requerido para a mudança de tara são 42 minutos.
- Mittlere Ereignisdauer: 44,0 min · laut Bericht: “Mudança de cápsula (trabalho interno)”
Wörtliches Zitat anzeigen
O diagrama indica que o trabalho interno de uma mudança de cápsula pode ser executado em 44 minutos e que, no total, o tempo requerido para a mudança de tara são 55 minutos.
- Mittlere Ereignisdauer: 69,0 min · laut Bericht: “Mudança de tara e cápsula (trabalho interno)”
Wörtliches Zitat anzeigen
O diagrama indica que o trabalho interno de uma mudança de tara e cápsula pode ser executado em 69 minutos e que, no total, o tempo requerido para a mudança de tara e cápsula são 84 minutos
- Application of the Concept of Total Productive Maintenance in Automatic Bottle Filling Machines (2019)Quelle öffnenAnteil an der Verlustzeit: 16,4 % · laut Bericht: “Set Up Losses”
Wörtliches Zitat anzeigen
Set Up Losses 5.220,00 16,36 2
- Application of the Concept of Total Productive Maintenance in Automatic Bottle Filling Machines (2019)Quelle öffnenVerlustzeit: 5.220 min · laut Bericht: “Set Up Losses”
Wörtliches Zitat anzeigen
Set Up Losses 5.220,00 16,36 2
- Mittlere Ereignisdauer: 69,0 min · laut Bericht: “Setup time”
Wörtliches Zitat anzeigen
Blowing machine Filling machine Labelling machine (bottleneck resource) Packaging machine 85 minutes 69 minutes 148 minutes 97 minutes 57 minutes 73 minutes 0 minutes 51 minutes
- Mittlere Ereignisdauer: 73,0 min · laut Bericht: “Idle time”
Wörtliches Zitat anzeigen
Blowing machine Filling machine Labelling machine (bottleneck resource) Packaging machine 85 minutes 69 minutes 148 minutes 97 minutes 57 minutes 73 minutes 0 minutes 51 minutes
- Peningkatan Efektivitas Mesin Susu Kental Manis dengan Metode Overall Equipment Effectiveness dan Diagram Ishikawa (2021)Quelle öffnenVerlustzeit: 6,60 jam · laut Bericht: “Setup & adjustment”
Wörtliches Zitat anzeigen
Failure = 97.2 Jam Setup & adjustment = 6.6 jam Downtime = 103.8 jam
- Set Up Time Reduction Using Single Minute Exchange of Dies (SMED) and 5S: A Case Study (2021)Quelle öffnenAnteil an der Verlustzeit: 48,0 % · laut Bericht: “setup time or line preparation time”
Wörtliches Zitat anzeigen
The most significant contribution of planned stoppages is 48% comes from setup time or line preparation time.
- Set Up Time Reduction Using Single Minute Exchange of Dies (SMED) and 5S: A Case Study (2021)Quelle öffnenAnteil an der Verlustzeit: 2,00 % · laut Bericht: “change over time”
Wörtliches Zitat anzeigen
The next is 34% of cleaning inspection and lubrication process, 19% of operational stoppages, 3% of meals or break, 2% of change over time, and the last 1% of planned maintenance.
- Set Up Time Reduction Using Single Minute Exchange of Dies (SMED) and 5S: A Case Study (2021)Quelle öffnenVerlustzeit: 34,0 min · laut Bericht: “Setup time”
Wörtliches Zitat anzeigen
Before the improvement of Single Minute Exchange of Dies (SMED), the actual setup activities are eight activities in total with 34 minutes to finish the setup activities
- Performance Analysis of Filling Machine Using Overall Equipment Effectiveness Metric in Beverage Company (2023)Quelle öffnenVerlustzeit: 2.235 min · laut Bericht: “Setup & Adjustment”
Wörtliches Zitat anzeigen
The second is Setup and Adjustment (30.7%), or equal to 2,235 minutes from data collection for December 2021 – March 2022.
- Performance Analysis of Filling Machine Using Overall Equipment Effectiveness Metric in Beverage Company (2023)Quelle öffnenAnteil an der Verlustzeit: 30,7 % · laut Bericht: “Setup & Adjustment”
Wörtliches Zitat anzeigen
The second is Setup and Adjustment (30.7%), or equal to 2,235 minutes from data collection for December 2021 – March 2022.
- Analisis Overall Equipment Effectiveness untuk Meningkatkan Efektivitas Mesin Filling Multiline pada PT-XYZ (2023)Quelle öffnenVerlustzeit: 27,1 jam · laut Bericht: “Setup and Adjustment Lossess”
Wörtliches Zitat anzeigen
Setup and Adjustment Lossess 27,10 27,10 53,66%
- Analisis Overall Equipment Effectiveness untuk Meningkatkan Efektivitas Mesin Filling Multiline pada PT-XYZ (2023)Quelle öffnenAnteil an der Verlustzeit: 53,7 % · laut Bericht: “Setup and Adjustment Lossess”
Wörtliches Zitat anzeigen
Losses terbesar yang terjadi pada filling multiline 01 adalah setup and adjustment losses yaitu sebesar 27,10 jam selama bulan maret tahun 2023 atau sebesar 53,66% dari total losses yang terjadi dalam proses produksi bumbu masak di mesin filling multiline 01.
- Using Lean Manufacturing Approach for Improvement in Food Manufacturing: Case Study from Egypt (2024)Quelle öffnenVerlustzeit: 18,0 min · laut Bericht: “Total time of setup”
Wörtliches Zitat anzeigen
Initial 18 11
- Using Lean Manufacturing Approach for Improvement in Food Manufacturing: Case Study from Egypt (2024)Quelle öffnenVerlustzeit: 11,0 min · laut Bericht: “Internal tasks time”
Wörtliches Zitat anzeigen
Initial 18 11
- Otomatisasi Perhitungan OEE pada Mesin Filling ILAPAK 50g Menggunakan PLC dan HMI (2024)Quelle öffnenVerlustzeit: 0 mnt · laut Bericht: “Setup & Adjustment”
Wörtliches Zitat anzeigen
2 Setup & Adjustment 0 0 20
- Otomatisasi Perhitungan OEE pada Mesin Filling ILAPAK 50g Menggunakan PLC dan HMI (2024)Quelle öffnenVerlustzeit: 0 mnt · laut Bericht: “Setup & Adjustment”
Wörtliches Zitat anzeigen
2 Setup & Adjustment 0 0 20
- Otomatisasi Perhitungan OEE pada Mesin Filling ILAPAK 50g Menggunakan PLC dan HMI (2024)Quelle öffnenVerlustzeit: 20,0 mnt · laut Bericht: “Setup & Adjustment”
Wörtliches Zitat anzeigen
2 Setup & Adjustment 0 0 20
- Lean and RCM-Based Production Model to Improve Operational Efficiency in the Production Line of a Peruvian Dairy SME (2025)Quelle öffnenAnteil an der Verlustzeit: 44,2 % · laut Bericht: “setup time delays”
Wörtliches Zitat anzeigen
The first reason had a lot of problems that caused the filling machine to break down often (55.8% of the problems) and setup time delays (44.2% of the inefficiencies).
- Lean and RCM-Based Production Model to Improve Operational Efficiency in the Production Line of a Peruvian Dairy SME (2025)Quelle öffnenVerlustzeit: 37,5 min · laut Bericht: “setup time”
Wörtliches Zitat anzeigen
The average setup time alone was 37.5 minutes, which made things much less efficient and cut down on effective working time.
- Lean and RCM-Based Production Model to Improve Operational Efficiency in the Production Line of a Peruvian Dairy SME (2025)Quelle öffnenVerlustzeit: 37,3 min · laut Bericht: “setup time”
Wörtliches Zitat anzeigen
The first setup took 37.3 minutes, but after using the method, it only took 16.3 minutes.
- Lean and RCM-Based Production Model to Improve Operational Efficiency in the Production Line of a Peruvian Dairy SME (2025)Quelle öffnenVerlustzeit: 16,4 min · laut Bericht: “setup time”
Wörtliches Zitat anzeigen
Setup Time minutes 37.5 18.75 16.39 -56%
- Lean and RCM-Based Production Model to Improve Operational Efficiency in the Production Line of a Peruvian Dairy SME (2025)Quelle öffnenVerlustzeit: 16,3 min · laut Bericht: “setup time”
Wörtliches Zitat anzeigen
The first setup took 37.3 minutes, but after using the method, it only took 16.3 minutes.
- Proposal for improvement to increase the overall equipment effectiveness (OEE) of a dairy products company through a Preventive Maintenance Plan, Standardized Work, and SMED (2025)Quelle öffnenAnteil an der geplanten Zeit: 1,15 % · laut Bericht: “Preparación de línea”
Wörtliches Zitat anzeigen
Preparación de línea Averías / Paros Reprocesos en envasado 1,15% 7,38% 6,35%
- Proposal for improvement to increase the overall equipment effectiveness (OEE) of a dairy products company through a Preventive Maintenance Plan, Standardized Work, and SMED (2025)Quelle öffnenAnteil an der geplanten Zeit: 1,15 % · laut Bericht: “Preparación de línea”
Wörtliches Zitat anzeigen
Preparación de línea Averías / Paros ELIMINADO 1,15% 1,00%
- Enhancing Productivity through Quick Changeovers: A SMED-Based Methodology in Manufacturing Industry (2026)Quelle öffnenVerlustzeit: 120 s · laut Bericht: “Filling machine setup”
Wörtliches Zitat anzeigen
4 Filling machine setup 120 120 -
- Enhancing Productivity through Quick Changeovers: A SMED-Based Methodology in Manufacturing Industry (2026)Quelle öffnenVerlustzeit: 120 s · laut Bericht: “Filling machine setup”
Wörtliches Zitat anzeigen
3 Filling machine setup 120 120 -
- Proposal to Improve the Operational Availability of the Canning Machine in a Craft Brewery through the Application of Work Study, SMED, and Planned Maintenance (2026)Quelle öffnenMittlere Ereignisdauer: 5,50 h · laut Bericht: “setup”
Wörtliches Zitat anzeigen
the average setup time was reduced from 7.25 h to 5.50 h
- Proposal to Improve the Operational Availability of the Canning Machine in a Craft Brewery through the Application of Work Study, SMED, and Planned Maintenance (2026)Quelle öffnenMittlere Ereignisdauer: 7,25 h · laut Bericht: “setup”
Wörtliches Zitat anzeigen
the average setup time was reduced from 7.25 h to 5.50 h

