foratvise
Get Started
Equipment failure (breakdowns)

Basic Condition and Operating Standard Non-Compliance

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 58 % of the line's lost time. Reported by 3 of the 112 studies that could observe it (limited evidence).

What happens

The packaging machine breaks down because fundamental equipment-care practices are not sustained: cleaning, lubrication and fastening are neglected, operators lack the skill to run and adjust the machine correctly, documented operating standards are not followed, and early signs of wear or misalignment go unnoticed until they cause a stoppage. Over time this unmanaged deterioration lowers the machine condition below the point where it can run reliably, producing breakdowns, bag jams, setup difficulties and calibration drift as secondary symptoms.

What is done about it

Implement autonomous and planned maintenance: restore and sustain basic conditions through cleaning, lubrication and inspection checklists, visually mark correct settings and fastener points, and train operators to a documented operating standard with periodic skill verification. Introduce condition monitoring and daily operator checks to detect deterioration early, and audit standard-operating-procedure adherence to prevent drift back to poor practice.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.1% [0.3–2.7%]
Expected share of lost time
0.6% [0.2–1.6%]
Share of lost time when present
58% [48–68%]
Studies / units
112 / 155
Evidence grade
C

Grade C: 2 to 4 studies, or an interval wider than 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.1% [0.2–3.6%]14 studies
  • Soft drinks, bottled water and juices
    1.2% [0.2–3.5%]33 studies
  • Brewing, wine and spirits
    1.1% [0.2–3.9%]14 studies
  • Bakery and pasta
    1.8% [0.3–6.2%]6 studies
  • Meat, poultry and seafood
    1.2% [0.2–4.1%]6 studies
  • Fruit and vegetable processing
    1.3% [0.2–4.3%]4 studies
  • Grain and oilseed milling
    1.3% [0.2–4.5%]4 studies
  • Sugar and confectionery
    1.3% [0.2–4.6%]4 studies
  • Snacks, coffee, tea and other foods
    1.2% [0.2–4.0%]8 studies
  • Animal feed and pet food
    1.8% [0.3–6.1%]5 studies
  • Food manufacturing (unspecified or mixed)
    1.1% [0.2–3.6%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The packaging machine breaks down because fundamental equipment-care practices are not sustained: cleaning, lubrication and fastening are neglected, operators lack the skill to run and adjust the machine correctly, documented operating standards are not followed, and early signs of wear or misalignment go unnoticed until they cause a stoppage. Over time this unmanaged deterioration lowers the machine condition below the point where it can run reliably, producing breakdowns, bag jams, setup difficulties and calibration drift as secondary symptoms.

How it looks in SCADA data

Engineering guidance

SCADA/MES shows recurrent unplanned stop events on the packaging machine attributed to varying, non-specific fault codes rather than a single repeatable component signature, interspersed with short minor stops (jams, fallen bags) and occasional setup or calibration-related state changes. Downtime reason logs entered by operators frequently reference skill, standard-compliance or condition-check categories rather than a discrete mechanical or electrical fault, and mean time between failures tends to drift downward without a clear single root cause in the historian.

Countermeasure

Engineering guidance

Implement autonomous and planned maintenance: restore and sustain basic conditions through cleaning, lubrication and inspection checklists, visually mark correct settings and fastener points, and train operators to a documented operating standard with periodic skill verification. Introduce condition monitoring and daily operator checks to detect deterioration early, and audit standard-operating-procedure adherence to prevent drift back to poor practice.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 119 Hr. · as reported: “Operating Standard not followed”
    Show verbatim quote
    4 Operating Standard not followed 13 119 25.00 100 25.54 100
  2. Number of events: 13.0 events · as reported: “Operating Standard not followed”
    Show verbatim quote
    4 Operating Standard not followed 13 119 25.00 100 25.54 100
  3. Lost time: 44.0 Hr. · as reported: “Operating Standard not followed”
    Show verbatim quote
    4 Operating Standard not followed 22 44 22.92 100 5.30 100
  4. Number of events: 22.0 events · as reported: “Operating Standard not followed”
    Show verbatim quote
    4 Operating Standard not followed 22 44 22.92 100 5.30 100
  5. Share of loss events: 25.0 % · as reported: “Operating Standard not followed”
    Show verbatim quote
    4 Operating Standard not followed 13 119 25.00 100 25.54 100
  6. Share of loss events: 22.9 % · as reported: “Operating Standard not followed”
    Show verbatim quote
    4 Operating Standard not followed 22 44 22.92 100 5.30 100
  7. Lost time: 111 Hr. · as reported: “Basic condition neglect”
    Show verbatim quote
    2 Basic condition neglect 13 111 25.00 44.20 23.82 42.91
  8. Number of events: 13.0 events · as reported: “Basic condition neglect”
    Show verbatim quote
    2 Basic condition neglect 13 111 25.00 44.20 23.82 42.91
  9. Lost time: 313 Hr. · as reported: “Basic condition neglect”
    Show verbatim quote
    2 Basic condition neglect 30 313 31.25 61.46 37.53 70.98
  10. Number of events: 30.0 events · as reported: “Basic condition neglect”
    Show verbatim quote
    2 Basic condition neglect 30 313 31.25 61.46 37.53 70.98
  11. Lost time: 279 Hr. · as reported: “Unchecked deterioration”
    Show verbatim quote
    1 Unchecked deterioration 29 279 30.21 30.21 33.45 33.45
  12. Number of events: 29.0 events · as reported: “Unchecked deterioration”
    Show verbatim quote
    1 Unchecked deterioration 29 279 30.21 30.21 33.45 33.45
  13. Lost time: 147 Hr. · as reported: “Inadequate skill level”
    Show verbatim quote
    3 Inadequate skill level 16 147 30.80 75.00 31.55 74.46
  14. Number of events: 16.0 events · as reported: “Inadequate skill level”
    Show verbatim quote
    3 Inadequate skill level 16 147 30.80 75.00 31.55 74.46
  15. Lost time: 89.0 Hr. · as reported: “Unchecked deterioration”
    Show verbatim quote
    1 Unchecked deterioration 10 89 19.20 19.20 19.09 19.09
  16. Number of events: 10.0 events · as reported: “Unchecked deterioration”
    Show verbatim quote
    1 Unchecked deterioration 10 89 19.20 19.20 19.09 19.09
  17. Lost time: 198 Hr. · as reported: “Inadequate skill level”
    Show verbatim quote
    3 Inadequate skill level 15 198 15.63 77.09 23.74 94.70
  18. Number of events: 15.0 events · as reported: “Inadequate skill level”
    Show verbatim quote
    3 Inadequate skill level 15 198 15.63 77.09 23.74 94.70
  19. Share of loss events: 25.0 % · as reported: “Basic condition neglect”
    Show verbatim quote
    2 Basic condition neglect 13 111 25.00 44.20 23.82 42.91
  20. Share of loss events: 31.3 % · as reported: “Basic condition neglect”
    Show verbatim quote
    2 Basic condition neglect 30 313 31.25 61.46 37.53 70.98
  21. Share of loss events: 30.2 % · as reported: “Unchecked deterioration”
    Show verbatim quote
    1 Unchecked deterioration 29 279 30.21 30.21 33.45 33.45
  22. Share of loss events: 30.8 % · as reported: “Inadequate skill level”
    Show verbatim quote
    3 Inadequate skill level 16 147 30.80 75.00 31.55 74.46
  23. Share of loss events: 19.2 % · as reported: “Unchecked deterioration”
    Show verbatim quote
    1 Unchecked deterioration 10 89 19.20 19.20 19.09 19.09
  24. Share of loss events: 15.6 % · as reported: “Inadequate skill level”
    Show verbatim quote
    3 Inadequate skill level 15 198 15.63 77.09 23.74 94.70
  25. Share of lost time: 33.5 % · as reported: “Unchecked deterioration”
    Show verbatim quote
    1 Unchecked deterioration 29 279 30.21 30.21 33.45 33.45
  26. Share of lost time: 37.5 % · as reported: “Basic condition neglect”
    Show verbatim quote
    2 Basic condition neglect 30 313 31.25 61.46 37.53 70.98
  27. Share of lost time: 23.7 % · as reported: “Inadequate skill level”
    Show verbatim quote
    3 Inadequate skill level 15 198 15.63 77.09 23.74 94.70
  28. Share of lost time: 5.30 % · as reported: “Operating Standard not followed”
    Show verbatim quote
    4 Operating Standard not followed 22 44 22.92 100 5.30 100
  29. Share of lost time: 19.1 % · as reported: “Unchecked deterioration”
    Show verbatim quote
    1 Unchecked deterioration 10 89 19.20 19.20 19.09 19.09
  30. Share of lost time: 23.8 % · as reported: “Basic condition neglect”
    Show verbatim quote
    2 Basic condition neglect 13 111 25.00 44.20 23.82 42.91
  31. Share of lost time: 31.6 % · as reported: “Inadequate skill level”
    Show verbatim quote
    3 Inadequate skill level 16 147 30.80 75.00 31.55 74.46
  32. Share of lost time: 25.5 % · as reported: “Operating Standard not followed”
    Show verbatim quote
    4 Operating Standard not followed 13 119 25.00 100 25.54 100
  33. Mean event duration: 97.0 min · as reported: “Setup time”
    Show verbatim quote
    Blowing machine Filling machine Labelling machine (bottleneck resource) Packaging machine 85 minutes 69 minutes 148 minutes 97 minutes 57 minutes 73 minutes 0 minutes 51 minutes
  34. Mean event duration: 51.0 min · as reported: “Idle time”
    Show verbatim quote
    Blowing machine Filling machine Labelling machine (bottleneck resource) Packaging machine 85 minutes 69 minutes 148 minutes 97 minutes 57 minutes 73 minutes 0 minutes 51 minutes
  35. Lost time: 40.0 min · as reported: “Packaging machine decalibration”
    Show verbatim quote
    Corrective maintenance time 33 min - 102 min - 40 min 20 min
  36. Lost time: 40.0 h · as reported: “Bags falling in machinery”
    Show verbatim quote
    bags stuck on conveyor Before packaging. Bags falling in machinery. Pallet flow issues. lmoroper bag attachment. Frequent stitching adjiustments. Hour 180 40 23 16 11 Cum % 67% 82% 90% 96% 100% 180 40 23 16 11