foratvise
Get Started
Process defects (scrap and rework)

Blow Molding Container Defects

Process defects (scrap and rework)QualityForming, moulding and depositing

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 3 of the 76 studies that could observe it (limited evidence).

What happens

During the blowing stage preforms are reheated and stretched against the mold under pneumatic pressure; uneven preform temperature, incorrect blow pressure or timing, or worn mold halves cause containers to come out with thin or uneven wall sections, deformation, haze, flash lines or incomplete forming. These out-of-specification bottles are separated from the good output as first-pass defects rather than reworked inline.

What is done about it

Calibrate and periodically verify the preform heating profile, blow pressure staging and mold cooling circuits, and perform preventive maintenance and inspection of mold halves and valves to prevent wear-related defects. Implement statistical monitoring of wall-thickness and visual inspection results to detect drift before it generates sustained defect rates.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.0% [0.2–2.7%]
Expected share of lost time
0.5% [0.1–1.3%]
Share of lost time when present
48% [36–60%]
Studies / units
76 / 96
Evidence grade
C

Grade C: 2 to 4 studies, or an interval wider than 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.2% [0.1–4.2%]5 studies
  • Soft drinks, bottled water and juices
    2.2% [0.3–7.7%]11 studies
  • Brewing, wine and spirits
    1.2% [0.1–4.7%]0 studies
  • Bakery and pasta
    1.0% [0.1–3.2%]25 studies
  • Meat, poultry and seafood
    1.2% [0.1–4.4%]3 studies
  • Fruit and vegetable processing
    1.2% [0.1–4.2%]3 studies
  • Grain and oilseed milling
    1.2% [0.1–4.7%]0 studies
  • Sugar and confectionery
    1.1% [0.1–4.0%]8 studies
  • Snacks, coffee, tea and other foods
    1.1% [0.1–4.2%]7 studies
  • Animal feed and pet food
    1.1% [0.1–4.1%]6 studies
  • Food manufacturing (unspecified or mixed)
    1.1% [0.1–4.0%]8 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During the blowing stage preforms are reheated and stretched against the mold under pneumatic pressure; uneven preform temperature, incorrect blow pressure or timing, or worn mold halves cause containers to come out with thin or uneven wall sections, deformation, haze, flash lines or incomplete forming. These out-of-specification bottles are separated from the good output as first-pass defects rather than reworked inline.

How it looks in SCADA data

Engineering guidance

MES/SCADA shows an elevated reject or scrap counter at the blow molder or downstream inspection station while the machine remains in running state, often correlated with blow pressure, oven temperature or mold cooling parameters drifting outside their normal band. No corresponding unplanned stop is recorded, confirming the loss is a quality rather than an availability event.

Countermeasure

Engineering guidance

Calibrate and periodically verify the preform heating profile, blow pressure staging and mold cooling circuits, and perform preventive maintenance and inspection of mold halves and valves to prevent wear-related defects. Implement statistical monitoring of wall-thickness and visual inspection results to detect drift before it generates sustained defect rates.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 14.8 h · as reported: “defect loss”
    Show verbatim quote
    This can reduce Filling 1 downtime from 393.78 hours to 67.62 hours and Blowing 1 from 91.35 hours to 14.75 hours.
  2. Mean event duration: 85.0 min · as reported: “Setup time”
    Show verbatim quote
    Blowing machine Filling machine Labelling machine (bottleneck resource) Packaging machine 85 minutes 69 minutes 148 minutes 97 minutes 57 minutes 73 minutes 0 minutes 51 minutes
  3. Mean event duration: 57.0 min · as reported: “Idle time”
    Show verbatim quote
    Blowing machine Filling machine Labelling machine (bottleneck resource) Packaging machine 85 minutes 69 minutes 148 minutes 97 minutes 57 minutes 73 minutes 0 minutes 51 minutes
  4. Share of lost time: 0.210 % · as reported: “Product Defect Losses”
    Show verbatim quote
    Rata - rata 6,10 0,95 11,47 0,00 0,00 0,21
  5. Defect rate: 88.0 % · as reported: “Proses Blowing”
    Show verbatim quote
    Proses Blowing 310042 88% 88%
  6. Number of events: 310,042 units · as reported: “Proses Blowing”
    Show verbatim quote
    Proses Blowing | 310042 | 88% | 88%
  7. Share of loss events: 88.0 % · as reported: “Proses Blowing”
    Show verbatim quote
    Proses Blowing | 310042 | 88% | 88%