foratvise
Get Started
Equipment failure (breakdowns)

Crown cap feed, strip and alignment malfunction at the crowner

Equipment failure (breakdowns)AvailabilityFilling

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 58 % of the line's lost time. Reported by 4 of the 120 studies that could observe it (limited evidence).

What happens

Crown caps travel from the hopper through a chute or rail to the crowner head, where worn or misaligned guide rails, head tooling or ring-pull fingers let caps jam, strip out of the feed track, or fail to seat squarely over the bottle. The same wear and misadjustment can leave the feed path partially obstructed or send an unseated cap through, producing an unsealed (uncrowned) container.

What is done about it

Inspect and replace worn guide rails, chute components and ring-pull/head tooling on a preventive schedule, and keep the cap feed path clean and lubricated to prevent strip-out and jamming. Standardize head and ring-pull setting procedures per format with documented reference values, and add or verify cap-presence sensing so unseated caps trigger a stop before an uncrowned bottle leaves the station.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.9% [0.2–2.3%]
Expected share of lost time
0.5% [0.1–1.3%]
Share of lost time when present
58% [47–67%]
Studies / units
120 / 162
Evidence grade
C

Grade C: 2 to 4 studies, or an interval wider than 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.0% [0.1–3.3%]18 studies
  • Soft drinks, bottled water and juices
    1.8% [0.4–4.7%]44 studies
  • Brewing, wine and spirits
    0.9% [0.1–3.0%]16 studies
  • Bakery and pasta
    1.1% [0.1–4.0%]0 studies
  • Meat, poultry and seafood
    1.0% [0.1–3.3%]6 studies
  • Fruit and vegetable processing
    1.1% [0.1–3.7%]4 studies
  • Grain and oilseed milling
    1.0% [0.1–3.5%]6 studies
  • Sugar and confectionery
    1.1% [0.1–3.7%]3 studies
  • Snacks, coffee, tea and other foods
    1.0% [0.1–3.3%]6 studies
  • Animal feed and pet food
    1.0% [0.1–3.6%]4 studies
  • Food manufacturing (unspecified or mixed)
    1.0% [0.1–3.4%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Crown caps travel from the hopper through a chute or rail to the crowner head, where worn or misaligned guide rails, head tooling or ring-pull fingers let caps jam, strip out of the feed track, or fail to seat squarely over the bottle. The same wear and misadjustment can leave the feed path partially obstructed or send an unseated cap through, producing an unsealed (uncrowned) container.

How it looks in SCADA data

Engineering guidance

MES/SCADA logs show repeated short stops or longer equipment-failure stops on the crowner with hopper-empty, feed-jam or cap-not-detected alarms, alternating with longer head-setting or ring-pull adjustment events after a format or tooling change. Upstream filler accumulation and downstream blocking signatures appear while the crowner is stopped, and the uncrowned-bottle defect counter at the downstream inspection point rises in parallel.

Countermeasure

Engineering guidance

Inspect and replace worn guide rails, chute components and ring-pull/head tooling on a preventive schedule, and keep the cap feed path clean and lubricated to prevent strip-out and jamming. Standardize head and ring-pull setting procedures per format with documented reference values, and add or verify cap-presence sensing so unseated caps trigger a stop before an uncrowned bottle leaves the station.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 24.0 min · as reported: “Crown hopper unit strip”
    Show verbatim quote
    Crown hopper unit strip 0 10 0 0 0 14 24 1.64
  2. Share of lost time: 1.64 % · as reported: “Crown hopper unit strip”
    Show verbatim quote
    Crown hopper unit strip 0 10 0 0 0 14 24 1.64
  3. Lost time: 616 min · as reported: “Crown stuck”
    Show verbatim quote
    Crown stuck 82 88 136 95 102 158 616 42.08
  4. Share of lost time: 42.1 % · as reported: “Crown stuck”
    Show verbatim quote
    Crown stuck 82 88 136 95 102 158 616 42.08
  5. Lost time: 15.0 min · as reported: “Crowner head setting”
    Show verbatim quote
    Crowner head setting 0 0 0 10 5 0 15 1.02
  6. Share of lost time: 1.02 % · as reported: “Crowner head setting”
    Show verbatim quote
    Crowner head setting 0 0 0 10 5 0 15 1.02
  7. Lost time: 47.0 min · as reported: “Ring pull setting”
    Show verbatim quote
    Ring pull setting 0 4 8 0 30 5 47 3.21
  8. Share of lost time: 3.21 % · as reported: “Ring pull setting”
    Show verbatim quote
    Ring pull setting 0 4 8 0 30 5 47 3.21
  9. Lost time: 10.0 min · as reported: “Crown hopper unit strip”
    Show verbatim quote
    4 | Crown hopper unit strip | 0 | 10 | 0 | 0 | 0 | 14 | 24 | 1.64
  10. Lost time: 14.0 min · as reported: “Crown hopper unit strip”
    Show verbatim quote
    4 | Crown hopper unit strip | 0 | 10 | 0 | 0 | 0 | 14 | 24 | 1.64
  11. Lost time: 15.0 min · as reported: “Crowner head setting”
    Show verbatim quote
    6 | Crowner head setting | 0 | 0 | 0 | 10 | 5 | 0 | 15 | 1.02
  12. Number of events: 3.00 events · as reported: “Crown path obstructed”
    Show verbatim quote
    5 Crown path obstructed 3 57 93%
  13. Number of events: 14,508 cases · as reported: “Uncrowned”
    Show verbatim quote
    Among these, underfill defects were the most frequent, with a total of 20,598 cases, followed by uncrowned bottles with 14,508 cases, and contamination with 8,124 cases.
  14. Share of lost time: 44.6 % · as reported: “Crowner and Carton Sealer combined”
    Show verbatim quote
    identifies the Crowner and Carton Sealer machines as critical bottlenecks with the highest accumulated downtime, together accounting for 44.58% of the total breakdown time.