foratvise
Get Started
Equipment failure (breakdowns)

Filling nozzle component failure

Equipment failure (breakdowns)AvailabilityFilling

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 57 % of the line's lost time. Reported by 1 of the 120 studies that could observe it (sparse evidence).

What happens

Filling nozzles contain wear parts such as O-rings, springs, seats and seals that degrade from repeated opening/closing cycles, product contact and cleaning chemicals, eventually losing sealing or metering function. Condensate, product residue or scale can also accumulate inside the nozzle body, restricting flow, causing dripping or preventing proper valve actuation until the part is cleaned or replaced.

What is done about it

Apply a preventive maintenance schedule for replacement of nozzle wear parts (O-rings, springs, seals) based on cycle counts, combined with routine inspection and cleaning of nozzle internals to remove condensate or product buildup. Monitor fill pressure and valve response per head to detect drift early and trigger proactive intervention before an unplanned stop occurs.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.6% [0.1–1.6%]
Expected share of lost time
0.3% [0.1–0.9%]
Share of lost time when present
57% [46–67%]
Studies / units
120 / 162
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.9% [0.1–3.2%]18 studies
  • Soft drinks, bottled water and juices
    0.5% [0.1–1.7%]44 studies
  • Brewing, wine and spirits
    0.6% [0.1–2.2%]16 studies
  • Bakery and pasta
    0.7% [0.1–2.7%]0 studies
  • Meat, poultry and seafood
    0.7% [0.1–2.4%]6 studies
  • Fruit and vegetable processing
    0.7% [0.1–2.5%]4 studies
  • Grain and oilseed milling
    0.7% [0.1–2.5%]6 studies
  • Sugar and confectionery
    0.7% [0.1–2.6%]3 studies
  • Snacks, coffee, tea and other foods
    0.7% [0.1–2.5%]6 studies
  • Animal feed and pet food
    0.7% [0.1–2.7%]4 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.4%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Filling nozzles contain wear parts such as O-rings, springs, seats and seals that degrade from repeated opening/closing cycles, product contact and cleaning chemicals, eventually losing sealing or metering function. Condensate, product residue or scale can also accumulate inside the nozzle body, restricting flow, causing dripping or preventing proper valve actuation until the part is cleaned or replaced.

How it looks in SCADA data

Engineering guidance

SCADA/MES data shows fault or fill-valve alarms localized to specific filling heads, recurring low-pressure or pressure-deviation flags on the filler manifold, and equipment-down states linked to a maintenance work order on the filling station. Repeated short stops escalating into longer stoppages on the same head, together with rising drip or giveaway trends before the fault, are typical patterns.

Countermeasure

Engineering guidance

Apply a preventive maintenance schedule for replacement of nozzle wear parts (O-rings, springs, seals) based on cycle counts, combined with routine inspection and cleaning of nozzle internals to remove condensate or product buildup. Monitor fill pressure and valve response per head to detect drift early and trigger proactive intervention before an unplanned stop occurs.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Time between events: 28,171 not reported · as reported: “Washing Nozzle”
    Show verbatim quote
    Waktu Kerusakan Weibull MTTF 28170,64
  2. Time between events: 34,691 not reported · as reported: “Nozzle Spring”
    Show verbatim quote
    Waktu Kerusakan Weibull MTTF 34691,22
  3. Time between events: 33,166 not reported · as reported: “Filling nozzle O-rings”
    Show verbatim quote
    Waktu Kerusakan Weibull MTTF 33166,2
  4. Mean event duration: 378 not reported · as reported: “Filling nozzle O-rings”
    Show verbatim quote
    Waktu Perbaikan Weibull MTTR 378
  5. Mean event duration: 226 not reported · as reported: “Nozzle Spring”
    Show verbatim quote
    Waktu Perbaikan Eksponensial MTTR 225,8
  6. Mean event duration: 217 not reported · as reported: “Washing Nozzle”
    Show verbatim quote
    Waktu Perbaikan Weibull MTTR 216,5179
  7. Number of events: 2.00 events · as reported: “Nozzle Condensat”
    Show verbatim quote
    Nozzle Condensat 2
  8. Time between events: 1,020 hours · as reported: “Nozzle Condensat”
    Show verbatim quote
    Nozzle Condensat 2 1020,2
  9. Lost time: 3.50 h · as reported: “Low nozzle pressure”
    Show verbatim quote
    Baja presión en boquillas 3,50 98%
  10. Lost time: 19.0 h · as reported: “Nozzle wear”
    Show verbatim quote
    Desgaste de boquillas 19,00 49%
  11. Lost time: 8.70 h · as reported: “Nozzle cleaning”
    Show verbatim quote
    Limpieza de boquillas 8,70 66%
  12. Lost time: 40.0 min · as reported: “Nozzle”
    Show verbatim quote
    Nozzle Rp260.000 Rp103.000 2 Jam 15 Menit 0 Jam 40 Menit