foratvise
Get Started
Idling and minor stops (micro-stops)

Packaging/filling seal and handling mechanism fault

Idling and minor stops (micro-stops)PerformancePackaging (forming, sealing, wrapping, case packing, palletizing)

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 52 % of the line's lost time. Reported by 2 of the 112 studies that could observe it (limited evidence).

What happens

Components that hold, position or seal the container during filling and packaging (sealing jaws, heat-sealing/induction elements, slings or belts that carry the pack through the machine) wear, lose tension or fall out of alignment. This produces incomplete or weak seals that leak, and at the same time causes the container or film to misfeed, jam or trigger a sensor fault that halts the machine.

What is done about it

Implement a preventive maintenance and inspection routine for sealing jaws, heating/induction elements and sling or belt tension, with periodic verification of seal integrity and mechanical alignment. Add sensors or seal-quality checks that flag degradation before it causes leaks or stoppages, and train operators to quickly clear jams while logging root cause.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.8% [0.2–2.0%]
Expected share of lost time
0.4% [0.1–1.1%]
Share of lost time when present
52% [40–64%]
Studies / units
112 / 155
Evidence grade
C

Grade C: 2 to 4 studies, or an interval wider than 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.8% [0.1–3.0%]14 studies
  • Soft drinks, bottled water and juices
    0.7% [0.1–2.2%]33 studies
  • Brewing, wine and spirits
    0.8% [0.1–2.9%]14 studies
  • Bakery and pasta
    0.9% [0.1–3.4%]6 studies
  • Meat, poultry and seafood
    0.9% [0.1–3.0%]6 studies
  • Fruit and vegetable processing
    0.9% [0.1–3.1%]4 studies
  • Grain and oilseed milling
    0.9% [0.1–3.1%]4 studies
  • Sugar and confectionery
    0.9% [0.1–3.3%]4 studies
  • Snacks, coffee, tea and other foods
    1.3% [0.2–4.5%]8 studies
  • Animal feed and pet food
    0.9% [0.1–3.6%]5 studies
  • Food manufacturing (unspecified or mixed)
    1.2% [0.1–4.2%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Components that hold, position or seal the container during filling and packaging (sealing jaws, heat-sealing/induction elements, slings or belts that carry the pack through the machine) wear, lose tension or fall out of alignment. This produces incomplete or weak seals that leak, and at the same time causes the container or film to misfeed, jam or trigger a sensor fault that halts the machine.

How it looks in SCADA data

Engineering guidance

Short, repeated machine-state transitions to stopped or fault without an associated maintenance work order, often logged as minor stops or jams on the sealing/packaging station; concurrently, quality or vision-inspection counters show rising rejects for leaking or poorly sealed packs. Upstream filling or capping stations may show blocking as the affected station accumulates stop time.

Countermeasure

Engineering guidance

Implement a preventive maintenance and inspection routine for sealing jaws, heating/induction elements and sling or belt tension, with periodic verification of seal integrity and mechanical alignment. Add sensors or seal-quality checks that flag degradation before it causes leaks or stoppages, and train operators to quickly clear jams while logging root cause.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 10.0 min · as reported: “HIP problem”
    Show verbatim quote
    HIP problem 0 0 10 0 0 0 10 0.68
  2. Share of lost time: 0.680 % · as reported: “HIP problem”
    Show verbatim quote
    HIP problem 0 0 10 0 0 0 10 0.68
  3. Defect rate: 0.270 % · as reported: “leakage problems”
    Show verbatim quote
    leakage problems reduced from 1.20% to 0.27%
  4. Defect rate: 1.20 % · as reported: “leakage problems”
    Show verbatim quote
    leakage problems reduced from 1.20% to 0.27%
  5. Number of events: 700 events · as reported: “slendang problem”
    Show verbatim quote
    slendang problem sebanyak 700 kejadian (15,11%)
  6. Share of loss events: 15.1 % · as reported: “slendang problem”
    Show verbatim quote
    slendang problem sebanyak 700 kejadian (15,11%)