In short
It appears in about 1 of every 100 lines studied.
When it appears, it takes on average about 64 % of the line's lost time. Reported by 3 of the 120 studies that could observe it (limited evidence).
What happens
Mechanical wear in valves, pistons or indexing mechanisms, together with product viscosity or container variability, forces the filler to run slower than its design rate to keep fill accuracy and avoid jams. The deficit accumulates as a continuous performance loss rather than as discrete stop events.
What is done about it
Perform scheduled calibration and wear-part replacement on filling valves, pumps and indexing drives, and validate speed-vs-viscosity or speed-vs-container curves so the line can run closer to its rated speed without quality risk.
Practical guidance written from engineering knowledge; it is not a statistical estimate.
1Probability and evidence
- Probability of presence
- 1.1% [0.3–2.7%]
- Expected share of lost time
- 0.7% [0.2–1.8%]
- Share of lost time when present
- 64% [51–75%]
- Studies / units
- 120 / 162
- Evidence grade
- C
Grade C: 2 to 4 studies, or an interval wider than 0.35.
2Probability by segment
- Dairy products1.1% [0.2–3.7%]18 studies
- Soft drinks, bottled water and juices1.5% [0.3–3.9%]44 studies
- Brewing, wine and spirits1.1% [0.2–3.6%]16 studies
- Bakery and pasta1.3% [0.2–4.9%]0 studies
- Meat, poultry and seafood1.2% [0.2–4.1%]6 studies
- Fruit and vegetable processing1.3% [0.2–4.2%]4 studies
- Grain and oilseed milling1.3% [0.2–4.1%]6 studies
- Sugar and confectionery1.3% [0.2–4.3%]3 studies
- Snacks, coffee, tea and other foods1.2% [0.2–4.1%]6 studies
- Animal feed and pet food1.3% [0.2–4.5%]4 studies
- Food manufacturing (unspecified or mixed)1.7% [0.2–5.7%]13 studies
3Mechanism, SCADA signature and countermeasure
Mechanism
Engineering guidanceMechanical wear in valves, pistons or indexing mechanisms, together with product viscosity or container variability, forces the filler to run slower than its design rate to keep fill accuracy and avoid jams. The deficit accumulates as a continuous performance loss rather than as discrete stop events.
How it looks in SCADA data
Engineering guidanceThe actual line speed or cycles-per-minute signal sits persistently below the setpoint while the machine remains in run state without stop alarms, producing a sustained gap between target and actual output and a depressed performance factor in OEE calculations.
Countermeasure
Engineering guidancePerform scheduled calibration and wear-part replacement on filling valves, pumps and indexing drives, and validate speed-vs-viscosity or speed-vs-container curves so the line can run closer to its rated speed without quality risk.
4Sources
- Efficiency Improvement of Glass Bottle Filler Machine Using Autonomous Maintenance-A Case Study (2025)Open sourceLost time: 459 min · as reported: “Speed loss”
Show verbatim quote
Speed loss 244 166 46 3 0 0 459 31.35
- Efficiency Improvement of Glass Bottle Filler Machine Using Autonomous Maintenance-A Case Study (2025)Open sourceShare of lost time: 31.4 % · as reported: “Speed loss”
Show verbatim quote
Speed loss 244 166 46 3 0 0 459 31.35
- Efficiency Improvement of Glass Bottle Filler Machine Using Autonomous Maintenance-A Case Study (2025)Open sourceLost time: 3.00 min · as reported: “Speed loss”
Show verbatim quote
17 | Speed loss | 244 | 166 | 46 | 3 | 0 | 0 | 459 | 31.35
- ANALISIS TOTAL PRODUCTIVE MAINTENANCE PADA LINE 8/CARBONATED SOFT DRINK PT COCA-COLA BOTTLING INDONESIA CENTRAL JAVA (2012)Open sourceLost time: 1,180 min · as reported: “speed filler”
Show verbatim quote
speed filler 37 1180 37 1180 33.03 33.56
- ANALISIS TOTAL PRODUCTIVE MAINTENANCE PADA LINE 8/CARBONATED SOFT DRINK PT COCA-COLA BOTTLING INDONESIA CENTRAL JAVA (2012)Open sourceNumber of events: 37.0 events · as reported: “speed filler”
Show verbatim quote
speed filler 37 1180 37 1180 33.03 33.56
- Lost time: 192 kg · as reported: “Idle operation with short-term stops of the equipment; Running of the equipment at a decreased speed”
Show verbatim quote
The loss in speed during the operation of the equipment led to a decrease in productivity by 192 kg., i.е. SD = 192 kg.
- Proposal for improvement to increase the overall equipment effectiveness (OEE) of a dairy products company through a Preventive Maintenance Plan, Standardized Work, and SMED (2025)Open sourceShare of planned time: 2.10 % · as reported: “Velocidad reducida”
Show verbatim quote
Charlas /Reuniones Velocidad reducida Defectuosos 1,50% 2,10% 0,05%
- Proposal for improvement to increase the overall equipment effectiveness (OEE) of a dairy products company through a Preventive Maintenance Plan, Standardized Work, and SMED (2025)Open sourceShare of planned time: 1.00 % · as reported: “Velocidad reducida”
Show verbatim quote
Charlas /Reuniones Velocidad reducida Defectuosos 1,50% 1,00% 0,05%
- Analysis of Filling Machine Effectiveness Using the Overall Equipment Effectiveness and Six Big Losses Method (2025)Open sourceShare of planned time: 6.77 % · as reported: “equipment operating below standard speed”
Show verbatim quote
losses due to equipment operating below standard speed with a losses value of 6.770%.

