foratvise
Get Started
Process defects (scrap and rework)

Heat seal defect (detached, wrinkled or folded seal)

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 48 % of the line's lost time. Reported by 2 of the 112 studies that could observe it (limited evidence).

What happens

On form-fill-seal packaging, the longitudinal (long) or transverse (center) seal fails to bond uniformly because jaw temperature, pressure or dwell time are out of range, the sealing surfaces are worn or contaminated, or the film is misaligned, wrinkled or tensioned unevenly as it passes through the jaws. The result is a seam that detaches under handling, or a seal line that shows wrinkles or folds that compromise package integrity.

What is done about it

Calibrate and periodically verify sealing jaw temperature, pressure and dwell time against the film specification, keep sealing surfaces clean and free of wear or nicks, and ensure consistent film tension and alignment through the jaws. Perform routine seal-integrity checks (visual, burst or peel tests) and adjust parameters at the first sign of drift before rejects accumulate.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.8% [0.2–2.1%]
Expected share of lost time
0.4% [0.1–1.0%]
Share of lost time when present
48% [36–59%]
Studies / units
112 / 155
Evidence grade
C

Grade C: 2 to 4 studies, or an interval wider than 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.9% [0.1–3.0%]14 studies
  • Soft drinks, bottled water and juices
    0.7% [0.1–2.2%]33 studies
  • Brewing, wine and spirits
    1.2% [0.2–4.0%]14 studies
  • Bakery and pasta
    0.9% [0.1–3.5%]6 studies
  • Meat, poultry and seafood
    0.9% [0.1–3.3%]6 studies
  • Fruit and vegetable processing
    0.9% [0.1–3.5%]4 studies
  • Grain and oilseed milling
    0.9% [0.1–3.6%]4 studies
  • Sugar and confectionery
    0.9% [0.1–3.4%]4 studies
  • Snacks, coffee, tea and other foods
    1.3% [0.2–4.6%]8 studies
  • Animal feed and pet food
    0.9% [0.1–3.1%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.9% [0.1–3.0%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

On form-fill-seal packaging, the longitudinal (long) or transverse (center) seal fails to bond uniformly because jaw temperature, pressure or dwell time are out of range, the sealing surfaces are worn or contaminated, or the film is misaligned, wrinkled or tensioned unevenly as it passes through the jaws. The result is a seam that detaches under handling, or a seal line that shows wrinkles or folds that compromise package integrity.

How it looks in SCADA data

Engineering guidance

The line keeps running without a stoppage, but the quality or vision inspection station registers a spike in sealed-package rejects classified by defect type (detached seal, wrinkled seal), often clustered by lane or by shift and correlated with jaw temperature or pressure trends drifting outside setpoint bands. No equipment-failure alarm is raised since the defect is caught only at inspection.

Countermeasure

Engineering guidance

Calibrate and periodically verify sealing jaw temperature, pressure and dwell time against the film specification, keep sealing surfaces clean and free of wear or nicks, and ensure consistent film tension and alignment through the jaws. Perform routine seal-integrity checks (visual, burst or peel tests) and adjust parameters at the first sign of drift before rejects accumulate.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Defect rate: 120,900 lbs/week · as reported: “bottom seal/end seal issues”
    Show verbatim quote
    Since centerlining the wrappers and running at ideal settings, at the close of the project, Company XYZ was running at 120,900 pounds of salvage per week.
  2. Share of lost time: 14.0 % · as reported: “rework caused by errors in the sealing process”
    Show verbatim quote
    This inefficiency was attributed to three main factors: rework, accounting for 13.95% of the issue, was caused by errors in the sealing process.
  3. Number of events: 112 kasus · as reported: “Seal terlipat”
    Show verbatim quote
    Seal terlipat 112 0,42 2,45
  4. Share of loss events: 2.45 % · as reported: “Seal terlipat”
    Show verbatim quote
    Seal terlipat 112 0,42 2,45
  5. Defect rate: 0.420 % · as reported: “Seal terlipat”
    Show verbatim quote
    Seal terlipat 112 0,42 2,45
  6. Share of loss events: 10.3 % · as reported: “Center seal detached (center seal lekang)”
    Show verbatim quote
    Diketahui bahwa kerusakan kemasan pada jenis kemasan melipat sebesar 17.4%, jenis kemasan selip 16.7%, jenis kemasan jepret 15.3%, center seal lekang 10.3%, longseal lekang 9.3%, koding hilang 8.8% kemasan acak 7.7%, seal berkerut 7.4%, ada sambungan 7.0%.
  7. Share of loss events: 9.30 % · as reported: “Long seal detached (longseal lekang)”
    Show verbatim quote
    Diketahui bahwa kerusakan kemasan pada jenis kemasan melipat sebesar 17.4%, jenis kemasan selip 16.7%, jenis kemasan jepret 15.3%, center seal lekang 10.3%, longseal lekang 9.3%, koding hilang 8.8% kemasan acak 7.7%, seal berkerut 7.4%, ada sambungan 7.0%.
  8. Share of loss events: 7.40 % · as reported: “Wrinkled seal (seal berkerut)”
    Show verbatim quote
    Diketahui bahwa kerusakan kemasan pada jenis kemasan melipat sebesar 17.4%, jenis kemasan selip 16.7%, jenis kemasan jepret 15.3%, center seal lekang 10.3%, longseal lekang 9.3%, koding hilang 8.8% kemasan acak 7.7%, seal berkerut 7.4%, ada sambungan 7.0%.
  9. Number of events: 32.0 bungkus · as reported: “Wrinkled seal (seal berkerut)”
    Show verbatim quote
    Seal Berkerut 32 90 6 6 38
  10. Number of events: 90.0 bungkus · as reported: “Wrinkled seal (seal berkerut)”
    Show verbatim quote
    Seal Berkerut 32 90 6 6 38
  11. Number of events: 6.00 bungkus · as reported: “Wrinkled seal (seal berkerut)”
    Show verbatim quote
    Seal Berkerut 32 90 6 6 38
  12. Number of events: 38.0 bungkus · as reported: “Wrinkled seal (seal berkerut)”
    Show verbatim quote
    Seal Berkerut 32 90 6 6 38
  13. Number of events: 29.0 bungkus · as reported: “Center seal detached (center seal lekang)”
    Show verbatim quote
    Center Seal Lekang 29 97 16 20 78
  14. Number of events: 97.0 bungkus · as reported: “Center seal detached (center seal lekang)”
    Show verbatim quote
    Center Seal Lekang 29 97 16 20 78
  15. Number of events: 16.0 bungkus · as reported: “Center seal detached (center seal lekang)”
    Show verbatim quote
    Center Seal Lekang 29 97 16 20 78
  16. Number of events: 20.0 bungkus · as reported: “Center seal detached (center seal lekang)”
    Show verbatim quote
    Center Seal Lekang 29 97 16 20 78
  17. Number of events: 78.0 bungkus · as reported: “Center seal detached (center seal lekang)”
    Show verbatim quote
    Center Seal Lekang 29 97 16 20 78
  18. Number of events: 35.0 bungkus · as reported: “Long seal detached (long seal lekang)”
    Show verbatim quote
    Long Seal Lekang 35 90 8 15 69
  19. Number of events: 90.0 bungkus · as reported: “Long seal detached (long seal lekang)”
    Show verbatim quote
    Long Seal Lekang 35 90 8 15 69
  20. Number of events: 8.00 bungkus · as reported: “Long seal detached (long seal lekang)”
    Show verbatim quote
    Long Seal Lekang 35 90 8 15 69
  21. Number of events: 15.0 bungkus · as reported: “Long seal detached (long seal lekang)”
    Show verbatim quote
    Long Seal Lekang 35 90 8 15 69
  22. Number of events: 69.0 bungkus · as reported: “Long seal detached (long seal lekang)”
    Show verbatim quote
    Long Seal Lekang 35 90 8 15 69