Unspecified minor stoppage on filling line
In short
It appears in about 1 of every 100 lines studied.
When it appears, it takes on average about 57 % of the line's lost time. Reported by 7 of the 120 studies that could observe it (good evidence).
What happens
The filler experiences brief interruptions arising from a variety of minor, uncatalogued disturbances (sensor blockages, small misfeeds, momentary jams, operator-cleared faults) that stop production without requiring maintenance intervention. Because the originating equipment or component is not identified in the source reports, these events are lumped together as a generic minor-stop category rather than a specific failure mode.
What is done about it
Perform a Pareto breakdown of micro-stop events by location and apparent trigger to reclassify the largest contributors into specific, actionable causes, and standardize operator clearing procedures to reduce recovery time. Where root causes remain diffuse, implement autonomous maintenance checks and sensor/guide adjustments on the filler to reduce the overall frequency of brief interruptions.
Practical guidance written from engineering knowledge; it is not a statistical estimate.
1Probability and evidence
- Probability of presence
- 1.5% [0.5–3.3%]
- Expected share of lost time
- 0.8% [0.3–1.9%]
- Share of lost time when present
- 57% [46–68%]
- Studies / units
- 120 / 162
- Evidence grade
- B
Grade B: 5 to 9 studies, or an interval width between 0.20 and 0.35.
2Probability by segment
- Dairy products1.5% [0.3–4.4%]18 studies
- Soft drinks, bottled water and juices1.8% [0.4–4.6%]44 studies
- Brewing, wine and spirits1.4% [0.2–4.2%]16 studies
- Bakery and pasta1.8% [0.3–6.1%]0 studies
- Meat, poultry and seafood1.6% [0.3–5.1%]6 studies
- Fruit and vegetable processing1.7% [0.3–5.5%]4 studies
- Grain and oilseed milling1.6% [0.2–4.9%]6 studies
- Sugar and confectionery1.7% [0.2–5.6%]3 studies
- Snacks, coffee, tea and other foods2.3% [0.4–7.5%]6 studies
- Animal feed and pet food1.7% [0.2–5.6%]4 studies
- Food manufacturing (unspecified or mixed)3.1% [0.5–9.3%]13 studies
3Mechanism, SCADA signature and countermeasure
Mechanism
Engineering guidanceThe filler experiences brief interruptions arising from a variety of minor, uncatalogued disturbances (sensor blockages, small misfeeds, momentary jams, operator-cleared faults) that stop production without requiring maintenance intervention. Because the originating equipment or component is not identified in the source reports, these events are lumped together as a generic minor-stop category rather than a specific failure mode.
How it looks in SCADA data
Engineering guidanceMES/SCADA logs show numerous short machine-state transitions to a stopped or fault state on the filler, each below the minor-stop duration threshold, often without a specific alarm code or with a generic 'minor stop' tag. Event counters accumulate a high frequency of brief stops relative to longer downtime events, and no single recurring component signal dominates the pattern.
Countermeasure
Engineering guidancePerform a Pareto breakdown of micro-stop events by location and apparent trigger to reclassify the largest contributors into specific, actionable causes, and standardize operator clearing procedures to reduce recovery time. Where root causes remain diffuse, implement autonomous maintenance checks and sensor/guide adjustments on the filler to reduce the overall frequency of brief interruptions.
4Sources
- Set Up Time Reduction Using Single Minute Exchange of Dies (SMED) and 5S: A Case Study (2021)Open sourceShare of lost time: 19.0 % · as reported: “operational stoppages”
Show verbatim quote
The next is 34% of cleaning inspection and lubrication process, 19% of operational stoppages, 3% of meals or break, 2% of change over time, and the last 1% of planned maintenance.
- Set Up Time Reduction Using Single Minute Exchange of Dies (SMED) and 5S: A Case Study (2021)Open sourceShare of lost time: 67.0 % · as reported: “planned stoppages”
Show verbatim quote
Based on the whole company manufacturing process, the highest number of waiting waste occurs in filling machines, especially for the planned stoppages with 67% compared with the 33% for the unplanned stoppages.
- Set Up Time Reduction Using Single Minute Exchange of Dies (SMED) and 5S: A Case Study (2021)Open sourceShare of lost time: 33.0 % · as reported: “unplanned stoppages”
Show verbatim quote
Based on the whole company manufacturing process, the highest number of waiting waste occurs in filling machines, especially for the planned stoppages with 67% compared with the 33% for the unplanned stoppages.
- Performance Analysis of Filling Machine Using Overall Equipment Effectiveness Metric in Beverage Company (2023)Open sourceLost time: 524 min · as reported: “Idling & Minor Stoppages”
Show verbatim quote
Idling & Minor Stoppages 524 7,2 98,6
- Performance Analysis of Filling Machine Using Overall Equipment Effectiveness Metric in Beverage Company (2023)Open sourceShare of lost time: 7.20 % · as reported: “Idling & Minor Stoppages”
Show verbatim quote
Idling & Minor Stoppages 524 7,2 98,6
- Analisis Produktivitas Mesin Filling Botol Dengan Metode Overal Equipment Effectiveness Dan Failure Mode And Effect Analysis (2023)Open sourceShare of loss events: 15.9 % · as reported: “Idle and Minor Stoppage”
Show verbatim quote
Reduce Speed Losses with an average proportion of 3.82% and a relative frequency of 39.01%, Downtime Losses with an average of 2.27% and a relative frequency of 28.31%, Defect Losses with an average of 1.58% and a relative frequency of 15.59%, Idle and Minor Stoppage with an average of 1.55% and a relative frequency of 15.85%.
- Analisis Produktivitas Mesin Filling Botol Dengan Metode Overal Equipment Effectiveness Dan Failure Mode And Effect Analysis (2023)Open sourceShare of planned time: 1.55 % · as reported: “Idle and Minor Stoppage”
Show verbatim quote
Reduce Speed Losses with an average proportion of 3.82% and a relative frequency of 39.01%, Downtime Losses with an average of 2.27% and a relative frequency of 28.31%, Defect Losses with an average of 1.58% and a relative frequency of 15.59%, Idle and Minor Stoppage with an average of 1.55% and a relative frequency of 15.85%.
- Lost time: 0 mnt · as reported: “Minor Stoppages”
Show verbatim quote
3 Minor Stoppases 0 0 87
- Lost time: 0 mnt · as reported: “Minor Stoppages”
Show verbatim quote
3 Minor Stoppases 0 0 87
- Lost time: 87.0 mnt · as reported: “Minor Stoppages”
Show verbatim quote
3 Minor Stoppases 0 0 87
- การพัฒนาโมเดลปัญญาประดิษฐ์เพื่อจำแนกเหตุการณ์การหยุดชะงักของเครื่องจักร ในระยะเวลาสั้น: กรณีศึกษาโรงงานผลิตเครื่องดื่ม (2026)Open sourceShare of loss events: 6.67 % · as reported: “Major-Minor Stoppage (Mi)”
Show verbatim quote
กลุม Major-Minor Stoppage (Mi) ซึ่งเปนเหตุการณที่มีความรุนแรงหรือเปนปญหาเรื้อรัง มีจํานวนนอยที่สุดเพียง 163 ครั้ง หรือคิดเปนรอยละ 6.67
- การพัฒนาโมเดลปัญญาประดิษฐ์เพื่อจำแนกเหตุการณ์การหยุดชะงักของเครื่องจักร ในระยะเวลาสั้น: กรณีศึกษาโรงงานผลิตเครื่องดื่ม (2026)Open sourceNumber of events: 163 events · as reported: “Major-Minor Stoppage (Mi)”
Show verbatim quote
กลุม Major-Minor Stoppage (Mi) ซึ่งเปนเหตุการณที่มีความรุนแรงหรือเปนปญหาเรื้อรัง มีจํานวนนอยที่สุดเพียง 163 ครั้ง หรือคิดเปนรอยละ 6.67
- การพัฒนาโมเดลปัญญาประดิษฐ์เพื่อจำแนกเหตุการณ์การหยุดชะงักของเครื่องจักร ในระยะเวลาสั้น: กรณีศึกษาโรงงานผลิตเครื่องดื่ม (2026)Open sourceNumber of events: 1,535 events · as reported: “General-Minor Stoppage (GM)”
Show verbatim quote
พบวาเหตุการณการหยุดชะงักชั่วคราวของเครื่องจักรในระยะสั้นสวนใหญจัดอยูในกลุม General-Minor Stoppage (GM) มีจํานวนสูงสุดถึง 1,535 ครั้ง คิดเปนรอยละ 62.83 ของขอมูลทั้งหมด
- การพัฒนาโมเดลปัญญาประดิษฐ์เพื่อจำแนกเหตุการณ์การหยุดชะงักของเครื่องจักร ในระยะเวลาสั้น: กรณีศึกษาโรงงานผลิตเครื่องดื่ม (2026)Open sourceShare of loss events: 62.8 % · as reported: “General-Minor Stoppage (GM)”
Show verbatim quote
พบวาเหตุการณการหยุดชะงักชั่วคราวของเครื่องจักรในระยะสั้นสวนใหญจัดอยูในกลุม General-Minor Stoppage (GM) มีจํานวนสูงสุดถึง 1,535 ครั้ง คิดเปนรอยละ 62.83 ของขอมูลทั้งหมด
- การพัฒนาโมเดลปัญญาประดิษฐ์เพื่อจำแนกเหตุการณ์การหยุดชะงักของเครื่องจักร ในระยะเวลาสั้น: กรณีศึกษาโรงงานผลิตเครื่องดื่ม (2026)Open sourceNumber of events: 745 events · as reported: “Non-Minor Stoppage (X)”
Show verbatim quote
รองลงมาคือ กลุม Non-Minor Stoppage (X) จํานวน 745 ครั้ง คิดเปนรอยละ 30.50
- การพัฒนาโมเดลปัญญาประดิษฐ์เพื่อจำแนกเหตุการณ์การหยุดชะงักของเครื่องจักร ในระยะเวลาสั้น: กรณีศึกษาโรงงานผลิตเครื่องดื่ม (2026)Open sourceShare of loss events: 30.5 % · as reported: “Non-Minor Stoppage (X)”
Show verbatim quote
รองลงมาคือ กลุม Non-Minor Stoppage (X) จํานวน 745 ครั้ง คิดเปนรอยละ 30.50

