foratvise
Get Started
Process defects (scrap and rework)

Packaging machine seal defects from component wear

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 47 % of the line's lost time. Reported by 1 of the 112 studies that could observe it (sparse evidence).

What happens

Wear of moving parts in the primary packaging machine, such as the magazine chain that feeds and positions packs, causes misalignment or inconsistent pressure and dwell time at the sealing station. This results in incomplete, wrinkled or weak seals on packages, and the same wear or jamming can also trigger unplanned stops of the machine that are logged as generic downtime.

What is done about it

Implement a preventive maintenance schedule for the magazine chain and sealing jaws based on cycle count, including lubrication, tension adjustment and timely replacement of worn links or guides. Add in-line seal quality checks with feedback to flag drift before it produces defective packages or triggers machine stoppages.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
0.6% [0.1–1.5%]
Expected share of lost time
0.3% [0.1–0.7%]
Share of lost time when present
47% [37–58%]
Studies / units
112 / 155
Evidence grade
D

Grade D: 0 or 1 study; the estimate is driven by partial pooling and priors, and the wide interval is the result.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    0.6% [0.1–2.3%]14 studies
  • Soft drinks, bottled water and juices
    0.5% [0.1–1.9%]33 studies
  • Brewing, wine and spirits
    0.9% [0.1–3.1%]14 studies
  • Bakery and pasta
    0.6% [0.1–2.4%]6 studies
  • Meat, poultry and seafood
    0.7% [0.1–2.5%]6 studies
  • Fruit and vegetable processing
    0.7% [0.1–2.5%]4 studies
  • Grain and oilseed milling
    0.7% [0.1–2.5%]4 studies
  • Sugar and confectionery
    0.7% [0.1–2.5%]4 studies
  • Snacks, coffee, tea and other foods
    0.6% [0.1–2.3%]8 studies
  • Animal feed and pet food
    0.7% [0.1–2.5%]5 studies
  • Food manufacturing (unspecified or mixed)
    0.6% [0.1–2.1%]14 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Wear of moving parts in the primary packaging machine, such as the magazine chain that feeds and positions packs, causes misalignment or inconsistent pressure and dwell time at the sealing station. This results in incomplete, wrinkled or weak seals on packages, and the same wear or jamming can also trigger unplanned stops of the machine that are logged as generic downtime.

How it looks in SCADA data

Engineering guidance

SCADA/MES shows elevated reject or rework counts at seal inspection stations, intermittent machine-state transitions to fault or stopped on the packaging machine without a clear maintenance code, and possible drift in sealing temperature or pressure sensor readings correlated with increasing cycle count since last chain service.

Countermeasure

Engineering guidance

Implement a preventive maintenance schedule for the magazine chain and sealing jaws based on cycle count, including lubrication, tension adjustment and timely replacement of worn links or guides. Add in-line seal quality checks with feedback to flag drift before it produces defective packages or triggers machine stoppages.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of lost time: 23.0 % · as reported: “poorly sealed packages”
    Show verbatim quote
    as a result there were poorly sealed packages, generating defective products, approximately 23% of the total loss in the production of type D biscuits.
  2. Share of lost time: 25.4 % · as reported: “downtime caused by the packaging machine”
    Show verbatim quote
    The downtime caused by the packaging machine during the four-week analysis was as long as 6 h 49 min which represented 25.43% of the overall downtime.
  3. Share of lost time: 11.5 % · as reported: “inadequate sealing of packaging”
    Show verbatim quote
    At the third level, the root causes were further detailed as clogging of cookies in conveyor belt chutes (55%), product fragility (13.5%), inadequate sealing of packaging (11.5%), and conveyor belt failures (20%).
  4. Share of lost time: 4.30 % · as reported: “wear on the magazine chain of the primary packaging machine”
    Show verbatim quote
    Additionally, 46.5% of the low performance was due to improper adjustment of the sealing system, and the presence of defective products was associated with wear on the magazine chain of the primary packaging machine, accounting for 4.3%.