Sterilizer piping and valve component failure
In short
It appears in about 6 of every 100 lines studied.
When it appears, it takes on average about 60 % of the line's lost time. Reported by 7 of the 34 studies that could observe it (good evidence).
What happens
Mechanical components of the sterilizer such as pipes, flanges, elbows, liners, nuts and pneumatic actuators suffer wear, corrosion, fatigue or loosening under repeated thermal and pressure cycling, leading to leaks, seizing or loss of actuation. This causes the sterilization process to stop until the damaged part is repaired or replaced by maintenance personnel.
What is done about it
Implement a preventive and predictive maintenance program covering piping, flanges, elbows, liners, nuts and actuators, including periodic inspection, torque verification, gasket and liner replacement schedules, and corrosion monitoring. Maintain critical spare parts on hand to shorten repair time when a failure occurs.
Practical guidance written from engineering knowledge; it is not a statistical estimate.
1Probability and evidence
- Probability of presence
- 6.2% [1.9–13.9%]
- Expected share of lost time
- 3.7% [1.1–8.3%]
- Share of lost time when present
- 60% [49–70%]
- Studies / units
- 34 / 37
- Evidence grade
- B
Grade B: 5 to 9 studies, or an interval width between 0.20 and 0.35.
2Probability by segment
- Dairy products6.2% [1.0–17.7%]5 studies
- Soft drinks, bottled water and juices6.5% [1.0–20.2%]2 studies
- Brewing, wine and spirits9.5% [1.7–28.2%]1 study
- Bakery and pasta7.1% [1.0–21.8%]0 studies
- Meat, poultry and seafood6.8% [1.0–20.8%]1 study
- Fruit and vegetable processing6.4% [1.0–18.6%]2 studies
- Grain and oilseed milling29% [8–60%]6 studies
- Sugar and confectionery6.3% [1.1–17.9%]3 studies
- Snacks, coffee, tea and other foods6.0% [0.9–17.2%]3 studies
- Animal feed and pet food6.2% [1.0–18.1%]4 studies
- Food manufacturing (unspecified or mixed)5.8% [1.0–16.4%]7 studies
3Mechanism, SCADA signature and countermeasure
Mechanism
Engineering guidanceMechanical components of the sterilizer such as pipes, flanges, elbows, liners, nuts and pneumatic actuators suffer wear, corrosion, fatigue or loosening under repeated thermal and pressure cycling, leading to leaks, seizing or loss of actuation. This causes the sterilization process to stop until the damaged part is repaired or replaced by maintenance personnel.
How it looks in SCADA data
Engineering guidanceSCADA/MES logs show the sterilizer entering an unplanned stop or fault state with alarms tied to pressure deviation, actuator position feedback mismatch, or valve and piping fault codes, often recurring on the same subsystem. These events appear as discrete downtime entries attributed to mechanical components rather than to process parameters, and may be followed by extended maintenance intervention time.
Countermeasure
Engineering guidanceImplement a preventive and predictive maintenance program covering piping, flanges, elbows, liners, nuts and actuators, including periodic inspection, torque verification, gasket and liner replacement schedules, and corrosion monitoring. Maintain critical spare parts on hand to shorten repair time when a failure occurs.
4Sources
- Analisa Perawatan Mesin Sterilizer Menggunakan Metode Overall Equipment Effectivenees (OEE) Pada PT. Djaja Putra Indonesia Kabupaten Asahan (2020)Open sourceShare of lost time: 61.5 % · as reported: “Equipment Failures”
Show verbatim quote
Faktor terbesar yang mempengaruhi efektifitas mesin Sterilizer dan menjadi prioritas untuk dieleminasi adalah faktor Equipment Failures sebesar 61,54% dan faktor Idling minor Stoppages sebesar 25,15%.
- Study on Preventive Maintenance Strategies of Filling Equipment Based on Reliability-Cantered Maintenance (2021)Open sourceLost time: 500 min · as reported: “SM”
Show verbatim quote
Total 2540 485 500 560 450 265 225 240 220 5485 224940 2.44%
- Study on Preventive Maintenance Strategies of Filling Equipment Based on Reliability-Cantered Maintenance (2021)Open sourceNumber of events: 24.0 events · as reported: “SM”
Show verbatim quote
Total 61 21 24 22 17 7 11 10 8 181
- ANALISA PERHITUNGAN OVERALL EQUIPMENT EFFECTIVENESS (OEE) PADA PROSES AWAL PENGOLAHAN KELAPA SAWIT DI PT. PERKEBUNAN NUSANTARA IV GUNUNG BAYU (2019)Open sourceShare of lost time: 0 % · as reported: “Rework Loss”
Show verbatim quote
Idling And Minor Stoppages by 0% and Rework Loss by 0%
- ANALISA PERHITUNGAN OVERALL EQUIPMENT EFFECTIVENESS (OEE) PADA PROSES AWAL PENGOLAHAN KELAPA SAWIT DI PT. PERKEBUNAN NUSANTARA IV GUNUNG BAYU (2019)Open sourceShare of lost time: 4.69 % · as reported: “Yield / Scrap Losses”
Show verbatim quote
Reduced Speed Losses by 67.54%, then Breakdown Lossses by 18.48%, Set Up and Adjustment Losses by 9.35%, Yield / Scrap Losses by 4.69 %, Idling And Minor Stoppages by 0% and Rework Loss by 0%
- ANALISA PERHITUNGAN OVERALL EQUIPMENT EFFECTIVENESS (OEE) PADA PROSES AWAL PENGOLAHAN KELAPA SAWIT DI PT. PERKEBUNAN NUSANTARA IV GUNUNG BAYU (2019)Open sourceShare of lost time: 9.35 % · as reported: “Set Up and Adjustment Losses”
Show verbatim quote
Reduced Speed Losses by 67.54%, then Breakdown Lossses by 18.48%, Set Up and Adjustment Losses by 9.35%, Yield / Scrap Losses by 4.69 %, Idling And Minor Stoppages by 0% and Rework Loss by 0%
- ANALISA PERHITUNGAN OVERALL EQUIPMENT EFFECTIVENESS (OEE) PADA PROSES AWAL PENGOLAHAN KELAPA SAWIT DI PT. PERKEBUNAN NUSANTARA IV GUNUNG BAYU (2019)Open sourceShare of lost time: 18.5 % · as reported: “Breakdown Losses”
Show verbatim quote
Reduced Speed Losses by 67.54%, then Breakdown Lossses by 18.48%, Set Up and Adjustment Losses by 9.35%, Yield / Scrap Losses by 4.69 %, Idling And Minor Stoppages by 0% and Rework Loss by 0%
- ANALISA PERHITUNGAN OVERALL EQUIPMENT EFFECTIVENESS (OEE) PADA PROSES AWAL PENGOLAHAN KELAPA SAWIT DI PT. PERKEBUNAN NUSANTARA IV GUNUNG BAYU (2019)Open sourceShare of lost time: 67.5 % · as reported: “Reduced Speed Losses”
Show verbatim quote
Reduced Speed Losses by 67.54%, then Breakdown Lossses by 18.48%, Set Up and Adjustment Losses by 9.35%, Yield / Scrap Losses by 4.69 %, Idling And Minor Stoppages by 0% and Rework Loss by 0%
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Open sourceNumber of events: 4.00 events · as reported: “Flange Pipe”
Show verbatim quote
Flange Pipe 4
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Open sourceNumber of events: 2.00 events · as reported: “Ball Valve”
Show verbatim quote
Ball Valve 2
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Open sourceNumber of events: 2.00 events · as reported: “Actuator”
Show verbatim quote
Actuator 2
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Open sourceNumber of events: 2.00 events · as reported: “Valve Exhaust”
Show verbatim quote
Valve Exhaust 2
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Open sourceNumber of events: 1.00 events · as reported: “Valve Condensat”
Show verbatim quote
Valve Condensat 1
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Open sourceNumber of events: 1.00 events · as reported: “Streiner Valve”
Show verbatim quote
Streiner Valve 1
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Open sourceTime between events: 510 hours · as reported: “Elbow”
Show verbatim quote
Elbow 4 510,1
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Open sourceTime between events: 510 hours · as reported: “Flange Pipe”
Show verbatim quote
Flange Pipe 4 510,1
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Open sourceTime between events: 680 hours · as reported: “Pipe”
Show verbatim quote
Pipe 3 680,13
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Open sourceTime between events: 1,020 hours · as reported: “Ball Valve”
Show verbatim quote
Ball Valve 2 1020,2
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Open sourceTime between events: 1,020 hours · as reported: “Liner”
Show verbatim quote
Liner 2 1020,2
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Open sourceTime between events: 1,020 hours · as reported: “Actuator”
Show verbatim quote
Actuator 2 1020,2
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Open sourceTime between events: 1,020 hours · as reported: “Valve Exhaust”
Show verbatim quote
Valve Exhaust 2 1020,2
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Open sourceTime between events: 2,040 hours · as reported: “Valve Condensat”
Show verbatim quote
Valve Condensat 1 2040
- Sterilizer Reliability Analysis Using Reliability Block Diagram Based on Failure Identification Through Fault Tree Analysis (2021)Open sourceTime between events: 2,040 hours · as reported: “Streiner Valve”
Show verbatim quote
Streiner Valve 1 2040
- Analisis Kelayakan Mesin Sterilizer Dengan Metode Overall Equipment Effectiveness (OEE) Pada PT. Hari Sawit Jaya Labuhanbatu, Sumatera Utara (2023)Open sourceLost time: 19,320 min · as reported: “planned downtime”
Show verbatim quote
selain itu terdapat total data dari planned downtime dari bulan Januari-Agustus 2023 adalah 19.320 menit.
- Analisis Kelayakan Mesin Sterilizer Dengan Metode Overall Equipment Effectiveness (OEE) Pada PT. Hari Sawit Jaya Labuhanbatu, Sumatera Utara (2023)Open sourceLost time: 22,786 min · as reported: “downtime mesin”
Show verbatim quote
Data dari Januari hingga Agustus 2023 mencapai 22.786 menit, yang berdampak negatif pada proses produksi.
- Penerapan Metode Total Productive Maintenance Dan Overall Equipment Effectiveness Pada Mesin Sterilizer Di PT. Tri Cahaya Sawit (2025)Open sourceLost time: 47.0 h/month · as reported: “downtime”
Show verbatim quote
tercatat bahwa mesin sterilizer mengalami downtime rata-rata 47 jam per bulan, dengan jumlah gangguan teknis mencapai 6–8 kali per bulan.
- Analisis Losses Minyak Sawit pada Proses Pengolahan Pabrik Kelapa Sawit PT Perkebunan Nusantara IV Regional IV Unit Usaha PKS Bunut (2026)Open sourceDefect rate: 0.0400 % · as reported: “USF (unstripped fruit)”
Show verbatim quote
Nilai rata-rata losses USF selama periode pengamatan tercatat sebesar 0,04%, sedangkan batas norma industri berada pada nilai 0,09%.
- Analisis Losses Minyak Sawit pada Proses Pengolahan Pabrik Kelapa Sawit PT Perkebunan Nusantara IV Regional IV Unit Usaha PKS Bunut (2026)Open sourceDefect rate: 0.370 % · as reported: “Janjangan kosong”
Show verbatim quote
Evaluasi terhadap janjang kosong memperlihatkan bahwa rata-rata losses berada pada nilai 0,37% dengan batas norma maksimum sebesar 0,44%.
- Analisis Losses Minyak Sawit pada Proses Pengolahan Pabrik Kelapa Sawit PT Perkebunan Nusantara IV Regional IV Unit Usaha PKS Bunut (2026)Open sourceDefect rate: 0.0900 % · as reported: “Nut”
Show verbatim quote
Nut 0,09 0,10 Mendekati batas

