Filler dosing/valve fault causing overfilling
In short
It appears in about 1 of every 100 lines studied.
When it appears, it takes on average about 47 % of the line's lost time. Reported by 3 of the 120 studies that could observe it (limited evidence).
What happens
Wear, misadjustment or sticking of the filler's dosing valve, nozzle or level/weight sensor allows more product than the target volume or weight into the container, often triggered by the same component degradation that can also cause the filler to stop unexpectedly. The fault may originate in a buffer tank feeding the filler, where level or pressure drift upsets the dosing accuracy downstream.
What is done about it
Implement preventive maintenance and periodic calibration of dosing valves, nozzles and level/weight sensors, with automatic shutdown or rejection when fill values exceed control limits, and stabilize upstream buffer-tank level/pressure control to keep feed conditions within the filler's design window.
Practical guidance written from engineering knowledge; it is not a statistical estimate.
1Probability and evidence
- Probability of presence
- 0.9% [0.2–2.1%]
- Expected share of lost time
- 0.4% [0.1–1.0%]
- Share of lost time when present
- 47% [35–58%]
- Studies / units
- 120 / 162
- Evidence grade
- C
Grade C: 2 to 4 studies, or an interval wider than 0.35.
2Probability by segment
- Dairy products0.9% [0.1–2.9%]18 studies
- Soft drinks, bottled water and juices1.7% [0.4–4.2%]44 studies
- Brewing, wine and spirits0.9% [0.1–3.0%]16 studies
- Bakery and pasta1.0% [0.1–3.6%]0 studies
- Meat, poultry and seafood1.0% [0.1–3.4%]6 studies
- Fruit and vegetable processing1.0% [0.1–3.5%]4 studies
- Grain and oilseed milling1.0% [0.1–3.6%]6 studies
- Sugar and confectionery1.0% [0.1–3.5%]3 studies
- Snacks, coffee, tea and other foods1.0% [0.1–3.3%]6 studies
- Animal feed and pet food1.0% [0.1–3.4%]4 studies
- Food manufacturing (unspecified or mixed)1.0% [0.1–3.3%]13 studies
3Mechanism, SCADA signature and countermeasure
Mechanism
Engineering guidanceWear, misadjustment or sticking of the filler's dosing valve, nozzle or level/weight sensor allows more product than the target volume or weight into the container, often triggered by the same component degradation that can also cause the filler to stop unexpectedly. The fault may originate in a buffer tank feeding the filler, where level or pressure drift upsets the dosing accuracy downstream.
How it looks in SCADA data
Engineering guidanceMES/SCADA shows fill-weight or fill-level readings drifting above the upper control limit on checkweigher or level-sensor trends, together with rejected-container counters rising; in parallel the filler state log may register fault or stop codes tied to the dosing valve, nozzle or buffer-tank level loop. Correlated buffer-tank level/pressure alarms preceding the overfill events help localize the root cause.
Countermeasure
Engineering guidanceImplement preventive maintenance and periodic calibration of dosing valves, nozzles and level/weight sensors, with automatic shutdown or rejection when fill values exceed control limits, and stabilize upstream buffer-tank level/pressure control to keep feed conditions within the filler's design window.
4Sources
- Analisa Efektifitas Mesin Palletizer Menggunakan Metode OEE Dan Identifikasi Kegagalan Dengan FMEA (2025)Open sourceLost time: 84.0 min · as reported: “Filling”
Show verbatim quote
1 Filling 84 25%
- Analisa Efektifitas Mesin Palletizer Menggunakan Metode OEE Dan Identifikasi Kegagalan Dengan FMEA (2025)Open sourceShare of lost time: 25.0 % · as reported: “Filling”
Show verbatim quote
1 Filling 84 25%
- Technical Analysis and Solutions to Reduce Scrap Rate In Liquid Filler Machine: Case Study: In Moha Soft Drink Production Line (2025)Open sourceNumber of events: 1,296 cases · as reported: “Out of space”
Show verbatim quote
Full breakage and out-of-space defects were less common, contributing 4,518 and 1,296 cases, respectively, across the study period.
- Improving Production Efficiency in a Chocolate SME through Continuous Flow, SMED and Poka-Yoke (2026)Open sourceDefect rate: 40.0 % · as reported: “overfilling”
Show verbatim quote
Overfilling: 40% → 6%
- Improving Production Efficiency in a Chocolate SME through Continuous Flow, SMED and Poka-Yoke (2026)Open sourceDefect rate: 6.00 % · as reported: “overfilling”
Show verbatim quote
Overfilling: 40% → 6%
- Penerapan Konsep Total Productive Maintenance (TPM) dalam Peningkatan Overall Equipment Effectiveness (OEE) pada Mesin Pengisian Botol di PT Trita Musi Prasada (2026)Open sourceLost time: 0 menit · as reported: “Scrap/Yield Loss”
Show verbatim quote
Scrap/Yield Loss 0 0% 100%
- Penerapan Konsep Total Productive Maintenance (TPM) dalam Peningkatan Overall Equipment Effectiveness (OEE) pada Mesin Pengisian Botol di PT Trita Musi Prasada (2026)Open sourceLost time: 0 menit · as reported: “Scrap/Yield Loss”
Show verbatim quote
Scrap/Yield Loss 0 0% 100%
- COMPARATIVE ANALYSIS OF PRODUCTION LINE EFFICIENCY UNDER VARYING DEMAND SCENARIOS USING MULTILAYER PERCEPTRON (2026)Open sourceDefect rate: 2.00 % · as reported: “Filler over/under fill, packaging”
Show verbatim quote
March 92,500 1,850 Filler over/under fill, packaging 2.0 Staff retraining initiated

