foratvise
Get Started
Idling and minor stops (micro-stops)

Minor stoppages on forming machines

Idling and minor stops (micro-stops)PerformanceForming, moulding and depositing

In short

It appears in about 2 of every 100 lines studied.

When it appears, it takes on average about 52 % of the line's lost time. Reported by 5 of the 76 studies that could observe it (good evidence).

What happens

Forming equipment such as presses, manual moulding machines and blow moulders experience frequent brief stops caused by material misfeeds, mould or die sticking, blocked sensors, or parts that fail to eject or advance correctly. These interruptions are cleared quickly by the operator through manual intervention, resetting or clearing the obstruction, without requiring maintenance.

What is done about it

Apply autonomous maintenance routines with operator checklists for mould cleaning and feed guide adjustment, improve material feed and part ejection mechanisms, and standardise quick-clearance procedures to shorten each stoppage. Root-cause the most frequent fault codes to redesign the feed path or sensor placement and reduce recurrence.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
2.2% [0.6–5.1%]
Expected share of lost time
1.1% [0.3–2.6%]
Share of lost time when present
52% [40–62%]
Studies / units
76 / 96
Evidence grade
B

Grade B: 5 to 9 studies, or an interval width between 0.20 and 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    2.4% [0.4–8.0%]5 studies
  • Soft drinks, bottled water and juices
    3.9% [0.7–10.9%]11 studies
  • Brewing, wine and spirits
    2.6% [0.4–8.6%]0 studies
  • Bakery and pasta
    2.4% [0.5–6.6%]25 studies
  • Meat, poultry and seafood
    3.7% [0.6–12.7%]3 studies
  • Fruit and vegetable processing
    2.5% [0.3–7.8%]3 studies
  • Grain and oilseed milling
    2.6% [0.4–8.8%]0 studies
  • Sugar and confectionery
    2.2% [0.3–7.0%]8 studies
  • Snacks, coffee, tea and other foods
    2.2% [0.3–6.9%]7 studies
  • Animal feed and pet food
    2.3% [0.3–7.5%]6 studies
  • Food manufacturing (unspecified or mixed)
    3.3% [0.5–10.3%]8 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

Forming equipment such as presses, manual moulding machines and blow moulders experience frequent brief stops caused by material misfeeds, mould or die sticking, blocked sensors, or parts that fail to eject or advance correctly. These interruptions are cleared quickly by the operator through manual intervention, resetting or clearing the obstruction, without requiring maintenance.

How it looks in SCADA data

Engineering guidance

MES/SCADA logs show numerous short transitions to a stopped or idle machine state interspersed within otherwise running periods, with cycle or stroke counters showing gaps rather than continuous increments. Alarm history reveals repeated low-severity faults (feed, mould, sensor) that are acknowledged and cleared rapidly by the operator without a maintenance work order being generated.

Countermeasure

Engineering guidance

Apply autonomous maintenance routines with operator checklists for mould cleaning and feed guide adjustment, improve material feed and part ejection mechanisms, and standardise quick-clearance procedures to shorten each stoppage. Root-cause the most frequent fault codes to redesign the feed path or sensor placement and reduce recurrence.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Share of planned time: 0.573 % · as reported: “Idle and Minor Stoppage Losses”
    Show verbatim quote
    = (240000−235754)𝑥 0,015 10200 = 0,573%
  2. Share of lost time: 2.50 % · as reported: “Idling & minor stoppages losses”
    Show verbatim quote
    Idling & minor stoppages losses 8,30 2,50 97,39
  3. Lost time: 8.30 jam · as reported: “Idling & minor stoppages losses”
    Show verbatim quote
    Idling & minor stoppages losses 8,30 2,50 97,39
  4. Share of lost time: 10.6 % · as reported: “Minor stoppage”
    Show verbatim quote
    Minor stoppage 6.30% 10.40% 15.00% 10.56%
  5. Share of lost time: 24.6 % · as reported: “idling & minor stoppages losses”
    Show verbatim quote
    the three biggest factors that caused the low value of machine effectiveness were idling & minor stoppages losses of 24.61%, yield losses of 24.37%, and reduced speed losses of 23.78%
  6. Share of lost time: 29.8 % · as reported: “Idle Minor Stoppage”
    Show verbatim quote
    The Six Big Losses analysis identified the two most dominant major losses, namely idle minor stoppage of 29.82% and reduce speed of 13.53%.
  7. Share of lost time: 11.5 % · as reported: “Idling & Minor Stoppage Losses”
    Show verbatim quote
    Rata - rata 6,10 0,95 11,47 0,00 0,00 0,21
  8. Share of lost time: 48.0 % · as reported: “idling and minor stoppages”
    Show verbatim quote
    The primary causes of low efficiency are idling and minor stoppages (48%) and equipment failures (28%), both of which are influenced by a lack of preventive maintenance and errors in machine settings.