Packaging Equipment Setup and Adjustment
In short
It appears in about 1 of every 100 lines studied.
When it appears, it takes on average about 55 % of the line's lost time. Reported by 3 of the 112 studies that could observe it (limited evidence).
What happens
During changeover or after drift from target settings, operators must manually adjust packaging machine parameters such as fill measurement, sealing position or mechanical stops to bring the equipment back to a correct running condition. This non-value-added adjustment time occurs between runs or after a product/format change and is not caused by a component breakdown.
What is done about it
Standardize changeover and adjustment procedures with pre-set recipes, quick-change tooling and go/no-go gauges, and apply SMED principles to separate internal and external setup tasks. Provide operators with guided HMI instructions and target setpoints to reduce the variability and duration of manual adjustments.
Practical guidance written from engineering knowledge; it is not a statistical estimate.
1Probability and evidence
- Probability of presence
- 1.0% [0.3–2.5%]
- Expected share of lost time
- 0.6% [0.1–1.4%]
- Share of lost time when present
- 55% [42–65%]
- Studies / units
- 112 / 155
- Evidence grade
- C
Grade C: 2 to 4 studies, or an interval wider than 0.35.
2Probability by segment
- Dairy products1.1% [0.1–3.7%]14 studies
- Soft drinks, bottled water and juices0.9% [0.1–2.7%]33 studies
- Brewing, wine and spirits1.5% [0.2–4.4%]14 studies
- Bakery and pasta1.7% [0.2–5.9%]6 studies
- Meat, poultry and seafood1.2% [0.2–4.1%]6 studies
- Fruit and vegetable processing1.2% [0.1–4.3%]4 studies
- Grain and oilseed milling1.7% [0.2–6.0%]4 studies
- Sugar and confectionery1.2% [0.2–4.0%]4 studies
- Snacks, coffee, tea and other foods1.1% [0.2–3.8%]8 studies
- Animal feed and pet food1.2% [0.2–4.0%]5 studies
- Food manufacturing (unspecified or mixed)1.1% [0.1–3.5%]14 studies
3Mechanism, SCADA signature and countermeasure
Mechanism
Engineering guidanceDuring changeover or after drift from target settings, operators must manually adjust packaging machine parameters such as fill measurement, sealing position or mechanical stops to bring the equipment back to a correct running condition. This non-value-added adjustment time occurs between runs or after a product/format change and is not caused by a component breakdown.
How it looks in SCADA data
Engineering guidanceThe line or machine state log shows a manual or adjustment mode with operator intervention flags rather than a fault/alarm code, often with repeated short stop-start cycles and parameter change entries clustered around changeover timestamps. Output counters remain near zero while the machine state indicates setup rather than running or faulted.
Countermeasure
Engineering guidanceStandardize changeover and adjustment procedures with pre-set recipes, quick-change tooling and go/no-go gauges, and apply SMED principles to separate internal and external setup tasks. Provide operators with guided HMI instructions and target setpoints to reduce the variability and duration of manual adjustments.
4Sources
- Use of packing equipment efficiency as an estimate of the overall plant effectiveness and as a tool to improve financial results of a food-processing unit (2017)Open sourceShare of lost time: 23.0 % · as reported: “mechanical adjustments”
Show verbatim quote
A deeper analysis of non-scheduled maintenance data (Figure 9) shows that major causes of packing equipment failure are related to: electrical failures (26%), unscheduled operational (26%) or mechanical (23%) adjustments, worn parts or equipment breakdown (13%) and automation failures (6%).
- Use of packing equipment efficiency as an estimate of the overall plant effectiveness and as a tool to improve financial results of a food-processing unit (2017)Open sourceShare of lost time: 26.0 % · as reported: “unscheduled operational adjustments”
Show verbatim quote
A deeper analysis of non-scheduled maintenance data (Figure 9) shows that major causes of packing equipment failure are related to: electrical failures (26%), unscheduled operational (26%) or mechanical (23%) adjustments, worn parts or equipment breakdown (13%) and automation failures (6%).
- Share of lost time: 23.9 % · as reported: “failures or adjustments of the packaging machine”
Show verbatim quote
The total number of failures or adjustments of all machines was 117 h, of which 23.93% were failures or adjustments of the packaging machine.
- Number of events: 23.0 events · as reported: “adjustment”
Show verbatim quote
During the four-week study, the largest number of events involved adjustment (23 events) and five were associated with a failure of the packaging machine.
- Share of lost time: 2.19 % · as reported: “Measurement Adjustment”
Show verbatim quote
Measurement Adjustment 2.19% 2.15% 1.49%
- Share of lost time: 1.49 % · as reported: “Measurement Adjustment”
Show verbatim quote
Measurement Adjustment 2.19% 2.15% 1.49%
- Penerapan Metode Overall Equipment Effectiveness (OEE) dan Six Big Losses untuk Mengukur Efektivitas Mesin Packing pada PT. Surya Tsabat Mandiri (2023)Open sourceShare of planned time: 5.06 % · as reported: “Setup and adjustment”
Show verbatim quote
3 Setup and adjustment 5,06 16,09 94,63
- Penerapan Metode Overall Equipment Effectiveness (OEE) dan Six Big Losses untuk Mengukur Efektivitas Mesin Packing pada PT. Surya Tsabat Mandiri (2023)Open sourceShare of lost time: 16.1 % · as reported: “Setup and adjustment”
Show verbatim quote
3 Setup and adjustment 5,06 16,09 94,63
- Improving Overall Equipment Effectiveness in the Packaging Process of Finished Cattle Feed: A Case Study of an Animal Feed Production Facility (2025)Open sourceLost time: 11.0 h · as reported: “Frequent stitching adjustments”
Show verbatim quote
bags stuck on conveyor Before packaging. Bags falling in machinery. Pallet flow issues. lmoroper bag attachment. Frequent stitching adjiustments. Hour 180 40 23 16 11 Cum % 67% 82% 90% 96% 100% 180 40 23 16 11

