Unspecified reduced-speed operation on packaging line
In short
It appears in about 2 of every 100 lines studied.
When it appears, it takes on average about 63 % of the line's lost time. Reported by 4 of the 112 studies that could observe it (limited evidence).
What happens
The packaging equipment runs below its rated or ideal cycle rate without a single identified fault being recorded; the slowdown results from an accumulation of minor mechanical wear, material handling constraints, or a conservative speed set point chosen by operators to avoid jams or defects.
What is done about it
Conduct a speed and bottleneck audit comparing actual cycle times against design rate for each station, restore mechanical tolerances and drive settings where wear is found, and standardize operator speed set points through training and documented run parameters.
Practical guidance written from engineering knowledge; it is not a statistical estimate.
1Probability and evidence
- Probability of presence
- 1.6% [0.5–3.6%]
- Expected share of lost time
- 1.0% [0.3–2.3%]
- Share of lost time when present
- 63% [50–74%]
- Studies / units
- 112 / 155
- Evidence grade
- C
Grade C: 2 to 4 studies, or an interval wider than 0.35.
2Probability by segment
- Dairy products1.6% [0.3–4.8%]14 studies
- Soft drinks, bottled water and juices1.2% [0.2–3.5%]33 studies
- Brewing, wine and spirits2.1% [0.4–6.2%]14 studies
- Bakery and pasta2.5% [0.4–8.4%]6 studies
- Meat, poultry and seafood1.7% [0.2–5.6%]6 studies
- Fruit and vegetable processing1.8% [0.3–5.8%]4 studies
- Grain and oilseed milling1.8% [0.3–5.7%]4 studies
- Sugar and confectionery1.8% [0.3–6.0%]4 studies
- Snacks, coffee, tea and other foods2.3% [0.4–7.3%]8 studies
- Animal feed and pet food1.8% [0.3–5.7%]5 studies
- Food manufacturing (unspecified or mixed)2.2% [0.4–6.3%]14 studies
3Mechanism, SCADA signature and countermeasure
Mechanism
Engineering guidanceThe packaging equipment runs below its rated or ideal cycle rate without a single identified fault being recorded; the slowdown results from an accumulation of minor mechanical wear, material handling constraints, or a conservative speed set point chosen by operators to avoid jams or defects.
How it looks in SCADA data
Engineering guidanceThe line or machine state remains in running mode without stop or fault alarms, yet the actual throughput or cycle-time counter is persistently below the nominal rate benchmark, producing a sustained gap between target and actual output during production time.
Countermeasure
Engineering guidanceConduct a speed and bottleneck audit comparing actual cycle times against design rate for each station, restore mechanical tolerances and drive settings where wear is found, and standardize operator speed set points through training and documented run parameters.
4Sources
- ANALISIS PENGUKURAN NILAI OVERALL EQUIPMENT EFFECTIVENESS (OEE) PADA PROSES PACKAGING DI LINE 2 (STUDI KASUS PT. MULTI BINTANG INDONESIA. TBK) (2016)Open sourceShare of planned time: 19.2 % · as reported: “Reduced Speed”
Show verbatim quote
Rata-rata 8833 0,0025 2773884,62 941,77 19,21
- Penerapan Metode Overall Equipment Effectiveness (OEE) dan Six Big Losses untuk Mengukur Efektivitas Mesin Packing pada PT. Surya Tsabat Mandiri (2023)Open sourceShare of planned time: 7.85 % · as reported: “Reduced speed”
Show verbatim quote
2 Reduced speed 7,85 24,96 78,54
- Penerapan Metode Overall Equipment Effectiveness (OEE) dan Six Big Losses untuk Mengukur Efektivitas Mesin Packing pada PT. Surya Tsabat Mandiri (2023)Open sourceShare of lost time: 25.0 % · as reported: “Reduced speed”
Show verbatim quote
2 Reduced speed 7,85 24,96 78,54
- Aggregate Analysis of Packaging Machine Effectiveness Using the OEE Method at PT. XYZ (2025)Open sourceShare of lost time: 0 % · as reported: “Reduced Speed Losses”
Show verbatim quote
Reduced Speed Losses 0 40.410 0% 100%
- Aggregate Analysis of Packaging Machine Effectiveness Using the OEE Method at PT. XYZ (2025)Open sourceLost time: 0 Minutes · as reported: “Reduced Speed Losses”
Show verbatim quote
Reduced Speed Losses 0 40.410 0% 100%
- Analisis Overall Equipment Effectiveness dan Six Big Losses pada Mesin Packaging Makanan di PT XYZ (2026)Open sourceLost time: 65.3 Jam · as reported: “Reduced Speed Losses”
Show verbatim quote
Kegagalan karena Reduced Speed Losses 65,28 24,73 Tinggi
- Analisis Overall Equipment Effectiveness dan Six Big Losses pada Mesin Packaging Makanan di PT XYZ (2026)Open sourceShare of lost time: 24.7 % · as reported: “Reduced Speed Losses”
Show verbatim quote
diketahui bahwa faktor kegagalan berasal dari Breakdown Losses sebesar 31,45%, Reduced Speed Losses sebesar 24,73%, dan Idling and Minor Stoppages sebesar 18,64%.
- Integrasi OEE–Pareto–FMEA–Ishikawa untuk Peningkatan Efektivitas Mesin dan Mutu Kemasan Kecap Pouch 550 mL: Integrated OEE–Pareto–FMEA–Ishikawa Approach for Improving Machine Effectiveness and Packaging Quality of 550 mL Soy Sauce Pouch (2026)Open sourceShare of lost time: 20.0 % · as reported: “Reduced speed loss”
Show verbatim quote
Reduced speed loss 20

