foratvise
Get Started
Process defects (scrap and rework)

Filling process quality defects

Process defects (scrap and rework)QualityFilling

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 50 % of the line's lost time. Reported by 7 of the 120 studies that could observe it (good evidence).

What happens

During otherwise stable filling operation, units are produced that fail to meet fill level, weight or container integrity specifications, typically due to valve wear, nozzle drip, product viscosity or density variation, or inconsistent dosing between heads. These non-conforming units are detected at or after the filler and must be scrapped, reworked or downgraded.

What is done about it

Apply statistical process control on fill weight or volume with automatic feedback to the dosing valves, schedule preventive calibration and replacement of wear-prone filling components, and verify incoming product viscosity or density consistency before filling.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.3% [0.4–3.1%]
Expected share of lost time
0.7% [0.2–1.6%]
Share of lost time when present
50% [39–61%]
Studies / units
120 / 162
Evidence grade
B

Grade B: 5 to 9 studies, or an interval width between 0.20 and 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    1.3% [0.2–4.1%]18 studies
  • Soft drinks, bottled water and juices
    2.7% [0.8–6.1%]44 studies
  • Brewing, wine and spirits
    1.3% [0.2–4.1%]16 studies
  • Bakery and pasta
    1.6% [0.2–5.9%]0 studies
  • Meat, poultry and seafood
    1.4% [0.2–4.4%]6 studies
  • Fruit and vegetable processing
    1.5% [0.2–4.8%]4 studies
  • Grain and oilseed milling
    1.5% [0.2–4.7%]6 studies
  • Sugar and confectionery
    1.6% [0.2–5.4%]3 studies
  • Snacks, coffee, tea and other foods
    2.0% [0.4–6.3%]6 studies
  • Animal feed and pet food
    1.5% [0.2–5.1%]4 studies
  • Food manufacturing (unspecified or mixed)
    1.4% [0.2–4.4%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

During otherwise stable filling operation, units are produced that fail to meet fill level, weight or container integrity specifications, typically due to valve wear, nozzle drip, product viscosity or density variation, or inconsistent dosing between heads. These non-conforming units are detected at or after the filler and must be scrapped, reworked or downgraded.

How it looks in SCADA data

Engineering guidance

Checkweigher, level sensor or vision inspection downstream of the filler logs an elevated reject or downgrade counter while the filling machine state remains in normal running mode. Fill weight or volume trend data shows drift or increased variance across heads without a corresponding stop event, distinguishing it from jam-related minor stops.

Countermeasure

Engineering guidance

Apply statistical process control on fill weight or volume with automatic feedback to the dosing valves, schedule preventive calibration and replacement of wear-prone filling components, and verify incoming product viscosity or density consistency before filling.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Defect rate: 3.00 % · as reported: “Discarded PET bottles (waste)”
    Show verbatim quote
    According to the history, the waste of these bottles was around 3%.
  2. Defect rate: 3.60 % · as reported: “Return/reuse of after-filling PET bottles”
    Show verbatim quote
    According to Table 3, an average of 3.6% of the bottles in good conditions of use was reutilized for new bottling processes.
  3. Share of lost time: 0.100 % · as reported: “Quality Defect and Yield Loses”
    Show verbatim quote
    Quality Defect and Yield Loses 32,50 0,10 5
  4. Lost time: 32.5 min · as reported: “Quality Defect and Yield Loses”
    Show verbatim quote
    Quality Defect and Yield Loses 32,50 0,10 5
  5. Defect rate: 0.0500 % · as reported: “Reject”
    Show verbatim quote
    52.10% 99.95% 0,05% 0% 100% 99.37% 99.32%
  6. Defect rate: 0 % · as reported: “Pending”
    Show verbatim quote
    52.10% 99.95% 0,05% 0% 100% 99.37% 99.32%
  7. Defect rate: 0.180 % · as reported: “Reject”
    Show verbatim quote
    13.70% 99.51% 0,18% 0.31% 100% 95.67% 95.20%
  8. Defect rate: 0.310 % · as reported: “Pending”
    Show verbatim quote
    13.70% 99.51% 0,18% 0.31% 100% 95.67% 95.20%
  9. Defect rate: 0.390 % · as reported: “Reject”
    Show verbatim quote
    8.57% 99.61% 0.39% 0% 100% 97.90% 97.52%
  10. Defect rate: 0 % · as reported: “Pending”
    Show verbatim quote
    8.57% 99.61% 0.39% 0% 100% 97.90% 97.52%
  11. Share of lost time: 8.00 % · as reported: “Defect Process”
    Show verbatim quote
    Defect Process 585 8 91,4
  12. Lost time: 585 min · as reported: “Defect Process”
    Show verbatim quote
    Defect Process 585 8 91,4
  13. Share of loss events: 15.6 % · as reported: “Defect Losses”
    Show verbatim quote
    Reduce Speed Losses with an average proportion of 3.82% and a relative frequency of 39.01%, Downtime Losses with an average of 2.27% and a relative frequency of 28.31%, Defect Losses with an average of 1.58% and a relative frequency of 15.59%, Idle and Minor Stoppage with an average of 1.55% and a relative frequency of 15.85%.
  14. Share of planned time: 1.58 % · as reported: “Defect Losses”
    Show verbatim quote
    Reduce Speed Losses with an average proportion of 3.82% and a relative frequency of 39.01%, Downtime Losses with an average of 2.27% and a relative frequency of 28.31%, Defect Losses with an average of 1.58% and a relative frequency of 15.59%, Idle and Minor Stoppage with an average of 1.55% and a relative frequency of 15.85%.
  15. Number of events: 2,134 bottles · as reported: “Reject Bottles”
    Show verbatim quote
    105334 2134 8 1.5 0.62 385
  16. Number of events: 2,483 bottles · as reported: “Reject Bottles”
    Show verbatim quote
    88883 2483 8 2 0.83 385
  17. Number of events: 2,359 bottles · as reported: “Reject Bottles”
    Show verbatim quote
    93559 2359 8 0.75 0.75 385
  18. Lost time: 3.40 jam · as reported: “Defect Losses”
    Show verbatim quote
    Defect Losses 3,40 48,93 96,88%
  19. Number of events: 49,044 cases · as reported: “Total scrap”
    Show verbatim quote
    Total | 20598 | 14508 | 8124 | 4518 | 1296 | 49044
  20. Number of events: 9.00 kaleng · as reported: “Produk Cacat / Reject”
    Show verbatim quote
    Produk Cacat / Reject (kaleng) 65 9 -56 kaleng
  21. Number of events: 65.0 kaleng · as reported: “Produk Cacat / Reject”
    Show verbatim quote
    Produk Cacat / Reject (kaleng) 65 9 -56 kaleng